Messages

1

20.7 Legacy Series / Re: Internet up and down lan port

« on: January 04, 2021, 11:35:44 am »

Ok I have taken the Opnsense firewall out :-( . Last night I disabled unbound, I thought if unbound is the issue and I disable it this would surely fix the problem. Nope nope and nope. After many restarts of Opnsense , my mesh network nodes and the Virgin media hub 3,  This problem is not going away. It will randomly work for a couple hours without any issues and then start dropping or renewing the lan IP address .. I soo want this to work but have no clue how to.

Currently running Virgin media hub in modem mode connected to Linksys Velop mesh in router mode.. all running perfect, but I have no control over my network now :-( .

Also @MBfromOK i tried the advised patch by you
but get the following error -  pkg: https://pkg.opnsense.org/FreeBSD:12:amd64/20.7/misc/unbound-1.13.0_1.txz: Not Found

2

20.7 Legacy Series / Re: Internet up and down lan port

« on: January 03, 2021, 11:24:36 am »

Thank you both, good to see active members here . Gives me encouragement to keep trying opnsense :-)
I will try the patch later and let you know what happened.
 
As this morning dhcp started to play up and down again,  I have disabled unbound .. let’s see if this helps for now

3

20.7 Legacy Series / Re: Internet up and down lan port

« on: January 02, 2021, 01:40:50 pm »

Hi, yes I haven’t changed anything so it’s on by default. Do you recommend it to be switched off ? And if so why ?
On the positive side since last night 7pm-ish I haven’t seen any connection drops. Maybe it’s fixed itself ?

4

20.7 Legacy Series / Internet up and down lan port

« on: January 01, 2021, 06:44:58 pm »

Hi all, I am new here and was wondering if any of you could help before I try another firewall.
I have an Intel atom E3845 device that came with pfsense on a 8gb cf card +2gb of ram. I have a 200mb virgin media connection and was suffering from random disconnects. I tried upgrading pfsense to a development version 2.5 hoping that this would fix my issue, but instead it killed my install, after sourcing a serial cable I reinstalled the system with opnsense  hoping that this would fix my issue. But sadly after spending an hour setting up 25 static ip addresses for all my devices and opening ports for our Nintendo game consoles I am facing exactly the same  issue now.

I want to throw in the towel with BSD and look at untangle or openwrt but wanted to give it one more last try by contacting this forum to see if I am missing something.

Let me explain my network setup (lan ip addresses set to 10.4.4.1 range)

Virgin media hub3 in modem mode >> opnsense igb0 (wan) igb3(lan) >>> linksys velop mesh wifi in bridge mode

If I take out the opnsense router and set the VM hub into router mode it all works fine  apart from the speed that goes up and down. To me this means that either the Opnsense router is doing something funky or the VM hub is being silly.

What do you guys think I should do? And which log files should I start checking?

Evrytime the internet goes down I see this in system/log files/general

usr/local/etc/rc.newwanip: On (IP address: 10.4.4.1) (interface: LAN[lan]) (real interface: igb3).   
usr/local/etc/rc.newwanip: IPv4 renewal is starting on 'igb3'   
usr/local/etc/rc.linkup: Hotplug event detected for LAN(lan) but ignoring since interface is configured with static IP (10.4.4.1)   
kernel   igb3: link state changed to UP   
usr/local/etc/rc.linkup: Hotplug event detected for LAN(lan) but ignoring since interface is configured with static IP (10.4.4.1)   
kernel   igb3: link state changed to DOWN