1
18.1 Legacy Series / Re: How to setup 2 NIC Opnsense vmware transparent
« on: March 14, 2018, 02:36:11 pm »
i am still struggling with this as whenever i create the bridge opnsense is no longer accessible?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
18.1 Legacy Series / Re: How to setup 2 NIC Opnsense vmware transparent
« on: March 09, 2018, 04:48:03 pm »
Thanks very much for the reply.
I set my router to bridge earlier, but when i follow the steps in the opnsense transparent bridge tutorial as SOON as i bridge WAN and LAN it throws me out of opensense gui and i cannot get back at all. the bridge step is only step 4 i think it was out of 10....
i must be missing something.
I set my router to bridge earlier, but when i follow the steps in the opnsense transparent bridge tutorial as SOON as i bridge WAN and LAN it throws me out of opensense gui and i cannot get back at all. the bridge step is only step 4 i think it was out of 10....
i must be missing something.
3
18.1 Legacy Series / Re: How to setup 2 NIC Opnsense vmware transparent
« on: March 09, 2018, 09:23:00 am »
Good day,
Thank you kindly for your reply.
If I may ask, why would it not work for traffic shaping?
What would my setup need to be should i want to run traffic shaping & caching proxy?
I have managed to get it working somewhat, however...when i create the bridge as per the transparent bridge tutorial it bombs and i no longer have access to the GUI.
If i set my adsl router to bridge mode must i create dialup in windows or opnsense?
Any advise would be welcome.
Regards,
Quintin
Thank you kindly for your reply.
If I may ask, why would it not work for traffic shaping?
What would my setup need to be should i want to run traffic shaping & caching proxy?
I have managed to get it working somewhat, however...when i create the bridge as per the transparent bridge tutorial it bombs and i no longer have access to the GUI.
If i set my adsl router to bridge mode must i create dialup in windows or opnsense?
Any advise would be welcome.
Regards,
Quintin
4
18.1 Legacy Series / Re: How to setup 2 NIC Opnsense vmware transparent
« on: March 08, 2018, 12:19:51 pm »
Is anyone able to assist me please to understand the VMware network config and pc config for 2 nics?
5
18.1 Legacy Series / How to setup 2 NIC Opnsense vmware transparent
« on: March 08, 2018, 07:51:17 am »
Hi all,
I am struggling to setup a 2 NIC opnsense VMWARE setup. I'm running VMware Workstation in windows.
Firstly, I am not 100% sure what the network adapter settings must be in VMWARE - bridge/nat/host etc. I am also confused with what my windows ip settings must be in order to get this to work. Do I bridge the two NIC's in windows?
I have the desktop pc with 2 NIC as seen in attached diagram. I want the WAN side to connect to adsl router 192.168.10.1. I then want to run opnsense transparently so that I can shape traffic etc going to the wireless router 192.168.10.200. the wireless router will then provide net access through opnsense to my clients.
PLEASE can someone help me as I am quite confused with the IP address and adapter setup.
I look forward to your response.
Kind regards,
Quintin
I am struggling to setup a 2 NIC opnsense VMWARE setup. I'm running VMware Workstation in windows.
Firstly, I am not 100% sure what the network adapter settings must be in VMWARE - bridge/nat/host etc. I am also confused with what my windows ip settings must be in order to get this to work. Do I bridge the two NIC's in windows?
I have the desktop pc with 2 NIC as seen in attached diagram. I want the WAN side to connect to adsl router 192.168.10.1. I then want to run opnsense transparently so that I can shape traffic etc going to the wireless router 192.168.10.200. the wireless router will then provide net access through opnsense to my clients.
PLEASE can someone help me as I am quite confused with the IP address and adapter setup.
I look forward to your response.
Kind regards,
Quintin
Pages: [1]