OPNsense Forum
International Forums => German - Deutsch => Topic started by: skotti on September 13, 2016, 10:17:05 am
-
Hallo,
nach mehreren pfsense-Installationen möchte ich nun die erste opnsense in Betrieb nehmen.
Leider kriege ich die Einwahl mittels PPPoE nicht zum laufen. Ich kann nirgendwo einen
Einwahlversuch erkennen.
# ps auxww | grep mpd
root 13570 0.0 0.1 50300 5460 - Ss 9:57AM 0:00.04 /usr/local/sbin/mpd5 -b -k -d /var/etc -f mpd_wan.conf -p /var/run/pppoe_wan.pid -s ppp pppoeclient
# cat /var/etc/mpd_wan.conf
startup:
# configure the console
set console close
# configure the web server
set web close
default:
pppoeclient:
create bundle static wan
set bundle enable ipv6cp
set iface name pppoe0
set iface route default
set iface disable on-demand
set iface idle 0
set iface enable tcpmssfix
set iface up-script /usr/local/sbin/ppp-linkup
set iface down-script /usr/local/sbin/ppp-linkdown
set ipcp ranges 0.0.0.0/0 0.0.0.0/0
set ipcp enable req-pri-dns
set ipcp enable req-sec-dns
create link static wan_link0 pppoe
set link action bundle wan
set link disable multilink
set link keep-alive 10 60
set link max-redial 0
set link disable chap pap
set link accept chap pap eap
set link disable incoming
set link mtu 1492
set auth authname "bnutzer@domain"
set auth password strenggeheim
set pppoe service "wf1"
set pppoe iface igb0
open
# ifconfig igb0
igb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=400bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWTSO>
ether 0c:c4:7a:7b:8f:b4
inet6 fe80::ec4:7aff:fe7b:8fb4%igb0 prefixlen 64 scopeid 0x1
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
# grep ppp /var/log/system.log
Sep 13 08:58:36 wsf opnsense: /interfaces.php: The command `/sbin/ifconfig 'pppoe0'' failed to execute
Sep 13 08:58:36 wsf opnsense: /interfaces.php: The command '/sbin/ifconfig 'pppoe0' inet6 -accept_rtadv' returned exit code '1', the output was 'ifconfig: interface pppoe0 does not exist'
Sep 13 08:58:36 wsf kernel: ng0: changing name to 'pppoe0'
Sep 13 09:55:22 wsf opnsense: /interfaces.php: The command `/sbin/ifconfig 'pppoe0'' failed to execute
Sep 13 09:55:22 wsf opnsense: /interfaces.php: The command '/sbin/ifconfig 'pppoe0' inet6 -accept_rtadv' returned exit code '1', the output was 'ifconfig: interface pppoe0 does not exist'
Sep 13 09:55:22 wsf kernel: ng0: changing name to 'pppoe0'
Sep 13 09:55:24 wsf opnsense: /interfaces.php: The command '/sbin/ifconfig 'pppoe0' -staticarp' returned exit code '1', the output was 'ifconfig: interface pppoe0 does not exist'
Sep 13 09:55:24 wsf opnsense: /interfaces.php: The command '/usr/sbin/arp -d -i 'pppoe0' -a > /dev/null 2>&1' returned exit code '1', the output was ''
Sep 13 09:55:26 wsf opnsense: /usr/local/etc/rc.linkup: The command `/sbin/ifconfig 'pppoe0'' failed to execute
Sep 13 09:55:26 wsf opnsense: /usr/local/etc/rc.linkup: The command '/sbin/ifconfig 'pppoe0' inet6 -accept_rtadv' returned exit code '1', the output was 'ifconfig: interface pppoe0 does not exist'
Sep 13 09:55:27 wsf kernel: ng0: changing name to 'pppoe0'
Sep 13 09:57:50 wsf opnsense: /usr/local/etc/rc.bootup: The command '/sbin/ifconfig 'pppoe0' inet6 -accept_rtadv' returned exit code '1', the output was 'ifconfig: interface pppoe0 does not exist'
Sep 13 09:57:50 wsf kernel: starting pppoe0 link...
Sep 13 09:57:50 wsf kernel: ng0: changing name to 'pppoe0'
# ifconfig pppoe0
pppoe0: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST> metric 0 mtu 1500
inet6 fe80::ec4:7aff:fe7b:8fb4%pppoe0 prefixlen 64 scopeid 0x9
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Haben die Fehlermeldungen in Bezug auf das Interface pppoe0 eine Bedeutung?
Bin ziemlich ratlos.
Grüße,
Skotti.
-
Ich hab' eben mal eine OpenWRT-Kiste zu Testzwecken an den Zugang
gesteckt - die Einwahl per PPPoE ging auf Anhieb.
Scheint danach am opnsense zu liegen.
Grüße, Skotti.
-
Ein Reset auf Factory-Defaults und eine anschliessende Neukonfiguration
hat das Problem gelöst.