1
23.1 Legacy Series / Re: Opnsense breaks with nothing fixing it
« on: August 11, 2023, 01:17:19 am »
So the power supply was the issue. I am happy that fixed the issue and wasnt something I did and was just a bad component.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
23.1 Legacy Series / Re: Opnsense breaks with nothing fixing it
« on: August 02, 2023, 07:33:54 am »
So far after I restarted the system and watched it all day I haven't seen any error popping up as of the moment but I shall keep monitoring it and report back if there is anything else that pops up after changing the power supply.
3
23.1 Legacy Series / Re: Opnsense breaks with nothing fixing it
« on: August 01, 2023, 05:08:03 pm »
I understand your point and in the name of getting rid of all the standard possibilities I shall do those things and report back in a few hours.
Bad power can cause disk problems, especially with vintage kit - see if you can swap it out as well
Next (usual) suspect is bad RAM. https://www.memtest86.com/
4
23.1 Legacy Series / Re: Opnsense breaks with nothing fixing it
« on: August 01, 2023, 11:03:33 am »Are you using the same PSU for both boards?Yes, I am. Why do you ask that?
5
23.1 Legacy Series / Opnsense breaks with nothing fixing it
« on: August 01, 2023, 12:01:12 am »
I am new to Opnsense and Unix-type OS with a little knowledge of Linux so my apologies for any misunderstandings.
I have been having an issue where I have installed Opnsense on 2 different SSDs with two different motherboards to some old computer hardware(shown at the bottom) that I had from an old setup and no matter what I do the install after about an hour sometimes longer will break with RRDtool page read error being the outcome. While that is breaking I can't do anything with the system and I have to restart before applying any changes to anything. I am not the best at getting the log files but I have been able to get some, but at different times in the troubleshooting process so I am not sure how helpful those will be. But after a while, I get a; ada0: <SAMSUNG MZ7LH480HAHQ-00005 HXT7404Q> s/n S45PNA0N247821 detached, with that being said I have tried many many different methods and installed methods with nothing working. This has been happening for months at this point and I have to keep switching back and forth between my old Netgear router and a fresh install of opnsense and have even tried pfsense with nothing working at the moment.
MB - gigabyte GA-A87-DEHP and gigabyte GA-Z97X-SLI
CPU - intel 4770 non k
RAM - DDR3 G-SKILl 32GB
1st - SSD was samsung 850 pro - 256gb
2nd - SSD and current Samsung pm883 - 480gb
NIC - 2.5G 2500m BASE-T intel I225 chip
I have been having an issue where I have installed Opnsense on 2 different SSDs with two different motherboards to some old computer hardware(shown at the bottom) that I had from an old setup and no matter what I do the install after about an hour sometimes longer will break with RRDtool page read error being the outcome. While that is breaking I can't do anything with the system and I have to restart before applying any changes to anything. I am not the best at getting the log files but I have been able to get some, but at different times in the troubleshooting process so I am not sure how helpful those will be. But after a while, I get a; ada0: <SAMSUNG MZ7LH480HAHQ-00005 HXT7404Q> s/n S45PNA0N247821 detached, with that being said I have tried many many different methods and installed methods with nothing working. This has been happening for months at this point and I have to keep switching back and forth between my old Netgear router and a fresh install of opnsense and have even tried pfsense with nothing working at the moment.
MB - gigabyte GA-A87-DEHP and gigabyte GA-Z97X-SLI
CPU - intel 4770 non k
RAM - DDR3 G-SKILl 32GB
1st - SSD was samsung 850 pro - 256gb
2nd - SSD and current Samsung pm883 - 480gb
NIC - 2.5G 2500m BASE-T intel I225 chip
Pages: [1]