Topics

[Don't reload, reboot or otherwise do anything here - just wqait and monitor the log indicating progress.]

After checking twice for upgrades on a fresh 25.7 install (see https://forum.opnsense.org/index.php?topic=49932.0), the process started as usual.

After some time I got a red popup indicating:

Code Select Expand

Danger
Unexpected error, check log for details
Don't reload, reboot or otherwise do anything here - just wqait and monitor the log indicating progress. It took me a couple of reinstalls and leaving this alone by chance once to realize after more than 10 minutes the upgrade had resumed and finished.

The red error popup happened around this time in the upgrade:

Code Select Expand

[20/97] Extracting nss-3.118.1: .......... done
[21/97] Upgrading zstd from 1.5.7 to 1.5.7_1...
[21/97] Extracting zstd-1.5.7_1: .......... done
[22/97] Upgrading boost-libs from 1.88.0_1 to 1.89.0_1...
[22/97] Extracting boost-libs-1.89.0_1:

Well, I tried to do that (check logs) but then accessing the web UI showed this instead:

Code Select Expand

403 Forbidden
After reinstalling and reaching the same stage in the upgrade, I noticed it resumed and kept going in the background (the log continued showing progress after a long time, at least 10 minutes).

I had enabled SSH access and connected during this process, everything looked normal with a busy pkg-static process indicating the upgrade continued.

Eventually as noted above the UI came back with the reboot message:

Code Select Expand

The upgrade has finished and the system is being rebooted at the moment, please wait...
In the background the log indicated a completed upgrade.

Upon reboot after a few more minutes the UI came back again prompting for login.

So, other than the worrying red error message, this time around the upgrade required much more time than usual, waiting it out was unusual but required.

Plan for this downtime next time you upgrade. :)

I was lucky this particular router has an easily accessible serial interface so I could monitor and check boot sequence. I have 2 other devices I accidentally bricked because I didn't wait, but they will require HDMI + keyboard to be fully reset.

For some reason on a fresh 25.7 I need to request a check for upgrades twice before it proceeds.

After installing version 25.7 on Velocloud 510, I attempted upgrading to 25.7.8.

I got this message in a popup:

Code Select Expand

Firmware status :
The release type "opnsense" is not available on this repository.
In the background, the output showed:

Code Select Expand

***GOT REQUEST TO CHECK FOR UPDATES***
Currently running OPNsense 25.7 (amd64) at Sun Nov 30 09:51:32 EST 2025
Fetching changelog information, please wait... done
Updating OPNsense repository catalogue...
Fetching meta.conf: . done
Fetching packagesite.pkg: .......... done
Processing entries: .......... done
OPNsense repository update completed. 911 packages processed.
All repositories are up to date.
Updating database digests format: .......... done
New version of pkg detected; it needs to be installed first.
The following 1 package(s) will be affected (of 0 checked):

Installed packages to be UPGRADED:
pkg: 1.19.2_5 -> 2.3.1_1

Number of packages to be upgraded: 1

The process will require 9 MiB more space.
6 MiB to be downloaded.
[1/1] Fetching pkg-2.3.1_1.pkg: .......... done
Checking integrity... done (0 conflicting)
[1/1] Upgrading pkg from 1.19.2_5 to 2.3.1_1...
[1/1] Extracting pkg-2.3.1_1: .......... done
pkg: Repository OPNsense cannot be opened. 'pkg update' required
Checking integrity... done (0 conflicting)
Your packages are up to date.
self: No packages available to install matching 'opnsense'
***DONE***
I am not sure why this happened but I requested a new check for upgrades and the check then proceeded normally, showing the changelog and proposing the upgrade.

I recently got three Velocloud EDGE 510 routers and installed OPNSense following the information from this previous post:

https://old.reddit.com/r/opnsense/comments/1mv3how/repurpose_velocloud_edge_510_router_wopnsense/

A few things changed and I was blocked at two spots, for some reason the default root password didn't work for me, etc. So I documented everything in detail including what didn't work for me, I hope it's useful and it encourages more people to try OPNsense with real hardware:
https://dulib.re/wiki/doku.php/opnsenseonvelocloudedge510

BTW if anyone knows where to start looking to have the ability to change the LED color, I'dlove to use that for some notifications, including after boot (I miss the sound other hardware do at boot) !

I can't seem to find any details about the Picture widget. What format & size work best ?

Hi,

I wanted to see used / total GB in the Disk widget, so I modified it and submitted a pull request.

If anyone needs this too, you can modify the Disk.js file directly too, here are the changes I've proposed (hoping it will make it in a future update):

https://github.com/opnsense/core/pull/9131