Messages

1

22.7 Legacy Series / Re: kernel trap 12 with interrupts disabled

« on: January 05, 2023, 08:23:36 pm »

Thanks!

Can you share some details where you were able to manually limit the PL2 to 12.5W and where you changed the turbo boost settings in the bios? I was trying to find it unsuccessfully. How's your Topton box performance and stability so far ?

Thanks.

2

22.7 Legacy Series / Re: kernel trap 12 with interrupts disabled

« on: November 03, 2022, 11:31:08 pm »

Hey.

No, I did not. I already have a protectli box for bare metal functionality, this unit was meant to test proxmox hypervisor functionality.

3

22.7 Legacy Series / Re: kernel trap 12 with interrupts disabled

« on: October 28, 2022, 02:35:45 am »

Hey !

Unfortunately, no, I abandoned this idea. The Topton unit is now sitting unused on a distant shelf. I also tried to replace the thermal paste as as I've seen in some of the different posts on the internet, but nothing helped. I used some test VM's to simulate iperf3 traffic through the firewall and it kept panicking after a few minutes.

4

22.7 Legacy Series / Re: OPNsense running in Proxmox on new Topton N6005 and keeps crashing.

« on: August 18, 2022, 09:09:06 am »

Thanks Vesalius. I did just that, and now i'm facing another issue - my speeds are half of my actual ISP speed. I have one OPNSense running native on a protectli box getting full speed, and when I move the lan/wan over to the OPNSense running in Proxmox I get half of that speed. Same config (xml) on both. I have assigned 4 cores (host type) + AES enabled in the VM, 8GB RAM and 64GB storage.

I'ver tried to apply some tunables I found online, and also disabled all HW offloading. So far no crashing.

I was also wondering what options I need to select for the PCI Passthrough of the NICs ? All-Functions? ROM-Bar? PCIExpress ?

5

22.7 Legacy Series / Re: OPNsense running in Proxmox on new Topton N6005 and keeps crashing.

« on: August 18, 2022, 04:07:57 am »

I'm hitting the same issue on the same device (Topton N6005 fro AliExpress) with 32GB ram and a 1TB PCIE NVME.
https://forum.opnsense.org/index.php?topic=29837.0

I did try to run OPNSense in UEFI mode (q35 machine) or the default, with the same results.

when i tried the bridge mode approach I couldn't figure out how exactly to set the bridges for WAN/LAN without going through the management bridge - any ideas to avoid problems ?

Thanks.

6

22.7 Legacy Series / kernel trap 12 with interrupts disabled

« on: August 13, 2022, 03:15:36 am »

Hello all !

I recently migrated from a dedicated machine (Protectli) to running OPNSense inside a VM (ProxMox) on a pentium N6005. I followed all the available guides, but for some reason my machine keeps panicking with the kernel trap 12. I looked around but all I could find were old versions of OPNSense pointing to resolved bugs. However, I'm using OPNsense 22.7.1 4b384de5c.

I keep hitting this repeatedly multiple times a day, the system will reboot and come back and ask me to submit a report, and then after some time will crash again.

Code: [Select]

WARNING: attempt to domain_add(netgraph) after domainfinalize()
ovpnc1: link state changed to UP
igc0: link state changed to UP
igc0_vlan50: link state changed to UP
igc0_vlan100: link state changed to UP
igc0_vlan20: link state changed to UP
igc0_vlan30: link state changed to UP
kernel trap 12 with interrupts disabled

I attached the full output I get when I sign into OPNSense after the crash happens (dmesg.boot).

I'm running the same config I used to run on the bare metal device, with the nic names adapted to the VM.

Any starting point and troubleshooting guides would be greatly appreciated !

Thanks.