Messages

1

22.1 Legacy Series / Re: Slow download thoughput from WAN on ESXi 7.0 after update to 22.1, upload OK

« on: January 30, 2022, 01:51:42 pm »

I have the same problem with a Virtualized OPNSense under Proxmox.

What I have also found is that if I run speedtest-cli from the OPNSense VM I get a normal download speed.

Edit: I also have VLANs on the WAN side

2

22.1 Legacy Series / Download speed dropped from 50Mb to 1Mb

« on: January 30, 2022, 01:46:13 pm »

Good afternoon,

I have a connection 50/50 Mb and OPNSense runs virtualized in a Proxmox VM.

Yesterday I upgraded OPNSense from 21.7.8 to 22.1 and after that my download speed dropped from 50Mb to something between 0 and 1.5Mb

Upload speed is still around 50Mb and ping is around 4 ms

Another test I did was running a speed test from the OPNSense VM (speedtest-cli) and there I got normal download speed.

I reinstalled the kernel but the problem persists.

Any suggestion?

3

21.7 Legacy Series / Re: Access GUI from WAN

« on: December 07, 2021, 10:49:21 pm »

I don't know what happened but I deleted the WAN rule and after creating it again it started working

Thanks for your help 

4

21.7 Legacy Series / Re: Access GUI from WAN

« on: December 07, 2021, 07:39:48 pm »

Here are the screenshots

WAN Rule:


Settings:

5

21.7 Legacy Series / Re: Access GUI from WAN

« on: December 07, 2021, 06:23:25 pm »

This is what I get when I do a packet capture in the WAN interface, protocol TCP and port 3443

I do not see any reply from OPNSense

Code: [Select]

Interface Capture output
WAN
vtnet0_vlan300 18:16:48.442074 IP My_Device_Public_IP.58564 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:16:48.442168 IP My_Device_Public_IP.58565 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:16:49.109031 IP My_Device_Public_IP.58566 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:05.741086 IP My_Device_Public_IP.58568 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:05.741130 IP My_Device_Public_IP.58567 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:05.980699 IP My_Device_Public_IP.58569 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:06.761665 IP My_Device_Public_IP.58567 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:06.761786 IP My_Device_Public_IP.58568 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:06.980710 IP My_Device_Public_IP.58569 > OPNSense_Public_IP.3443: tcp 0
WAN
vtnet0_vlan300 18:17:08.740577 IP My_Device_Public_IP.58567 > OPNSense_Public_IP.3443: tcp 0

6

21.7 Legacy Series / Re: Access GUI from WAN

« on: December 07, 2021, 04:02:48 pm »

Yes, mi port there is 3443

From the LAN side I open the GUI using OPNSense_IP:3443

I do not have any port forwarding configured

Regards

7

21.7 Legacy Series / Re: Access GUI from WAN

« on: December 07, 2021, 03:47:44 pm »

Yes, I know it is not safe  . This rule will be normally disabled and I temporarily enable it using the VPN in my phone because on my laptop at work I cannot connect using the VPN.

By webserver you mean System - Settings - Administration - Listen interfaces? I have it set to "All"


Regards

8

21.7 Legacy Series / Access GUI from WAN

« on: December 07, 2021, 03:18:43 pm »

Good afternoon,

I'm trying to access the GUI from the WAN side but so far I have not been able to get it.

I have reviewed several old posts and have done the following:

Firewall - Rules - WAN

Action: pass
Interface: WAN
Protocol: TCP
Source: Any
Destination: WAN Address
Destination port range: 3443
Reply-to: Disable

But when I try to connect from outside my LAN with publicIP:3443 I get:

Code: [Select]

Network Error (tcp_error)
A communication error occurred: ""
The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
Anyone have any idea how to fix this?

9

21.1 Legacy Series / Captive portal not redirecting in version 21.1.5

« on: May 05, 2021, 02:01:33 pm »

Goof afternoon,

I just installed OPNsense and I can't get the captive portal to work properly.

I have it assigned to my Guests interface; my phone gets a DHCP IP address but it is not redirected to the login page. If I enter the page opnsense_ip:8000 manually it is available

With my previous installation (pfSense) a notification appeared in the top bar and when clicked I was sent to the login page

Does anyone know how to solve or debug this?