Messages

1

23.1 Legacy Series / Can’t create IPv6 Gateway

« on: March 02, 2023, 03:41:25 am »

[img]I have public IPv6 space I was routing to my house via a routed IPsec tunnel. Had everything working great, sometime it stopped working. I went ahead to set up in the new connection and was able to get the phase 1 connection working. Went to set ip routes and gateways and I can create the IPv6 gateway. I select an IPv6 interface type and am using and IPv6 address, but just get an error that an IPv6 address is not detected.

2

General Discussion / Re: PHP Memory exhaustion errors

« on: March 05, 2022, 04:37:55 am »

I reported the error with the crash reporter.  Are you on 22.1.2_1 ?

Also I have loads. of memory 12+GB Free right now

3

General Discussion / Re: PHP Memory exhaustion errors

« on: March 05, 2022, 03:15:48 am »

Seeing the same error.

line 95 of that file is

exec('opnsense-log dhcpd 2> /dev/null', $log, $ret);

looking into my dhcp settings.  I habe multiple dhcpv4 and dcpv6 subnets and server instances running.

4

Hardware and Performance / Re: Intel pro 1000/ mt slow throupuy

« on: February 27, 2022, 03:13:23 am »

Old CPU, do you have spectre and meltdown enabled? They are by default. What about your power settings? Forcing power saving I the bios or with powerd could be impacting you as well.

5

22.1 Legacy Series / Re: CPU utilization much higher than with pfSense

« on: February 27, 2022, 03:05:02 am »

The NIC offload settings are located under interfaces>advanced in opnsense. By default all offloading is disabled.

6

General Discussion / Re: Unbound-control and SNMP extend

« on: February 11, 2022, 08:26:32 pm »

Same problem.  My search brought me here.

unbound-control isnt a service to run, but is enabled with unbound configuration in opnsense.

I learned you have to specify the unbound configuration.

Code: [Select]

unbound-control -c /var/unbound/unbound.conf stats
Returns results.  Just need to figure out how to get the extend configuration to persist through a reboot in the snmp configuration.

7

Hardware and Performance / Re: Intel 82576 (Pro/1000VT) crashing system

« on: February 10, 2022, 05:36:30 pm »

Have you tried updating the nic firmware?

8

21.7 Legacy Series / Re: NTP Issue

« on: January 27, 2022, 10:16:38 pm »

After multiple service restarts, and reboots, started working when I stopped looking at it.  I know it can take time to sync to timeservers, maybe I just wan't patient enough for the 4 hours it seemed to take.

9

21.7 Legacy Series / NTP Issue

« on: January 27, 2022, 04:44:31 pm »

On 21.7.8, I am unable to pull ntp peer stats via the gui, or on the CLI

Code: [Select]

root@oob-router:~ # ntpq -p
No association ID's returned
Logs just show an expected unsyncronized clock message, and listing all interfaces the daemon is listening on.

Any troubleshooting ideas?

10

22.1 Legacy Series / Any performance chnages in 22.1?

« on: January 13, 2022, 03:05:23 pm »

Has anyone noticed any performance changes? Good or bad?  Plan on installing on a lab router later today and was just curious.

11

21.7 Legacy Series / Re: Weird CPU useage

« on: November 04, 2021, 09:40:59 pm »

Thanks.

I brought it back to mainstream, saw the CPU weirdness, and ran the ifconfig directly on the terminal.

I have 18 interfaces total, took 6-7 seconds for them all to populate.

12

21.7 Legacy Series / Re: Weird CPU useage

« on: November 04, 2021, 09:23:24 pm »

How do undo

opnsense-patch 5acaca4 913afdb

so that I can test?

13

21.7 Legacy Series / Re: Weird CPU useage

« on: November 04, 2021, 09:17:19 pm »

Your inference is correct, turning off the offloading features made no difference.

I think you have it narrowed to something fixed in the patch/commit that your shared is causing the issue.

14

21.7 Legacy Series / Re: Weird CPU useage

« on: November 04, 2021, 09:05:32 pm »

yes it is ix0, ix1, ix2....

15

21.7 Legacy Series / Re: Weird CPU useage

« on: November 04, 2021, 09:04:29 pm »

You are correct using the ix driver.  This motherboard has 6 10GbE interfaces using the ix driver, and I have two more on the intel card.

I am using hardware for CSC, TSO, LRO, and VLAN filtering across the ix interfaces.