Show Posts
1
20.1 Legacy Series / LTE-USB-Stick (Huawei E3372h-320 Hilink) on OPNSense as LTE-Fallback
« on: July 14, 2020, 09:30:49 am »
Hello dear community,
after spending almost 10h in trying to flash the E3372 into stickmode for proper support of AT-Commands, i just threw the towel (before almost all my hair has fallen out...) and wanted to try out the LTE-Stick in NDIS-Mode on the OPNSense.
Unfortunately the stick somehow is getting connected and disconnected over and over again, without holding that connection.
Here's my dmesg-output:
The stick is directly connected with the APU2C4 via the BackUSB-Ports and as far as i've read on the documentation should be supported by the OS.
Is there any prior preparation to be done to support this stick properly, or what am i missing here?
I am planning to use this stick as LTE-Failover-Connection in case my main line is getting disconnected.
Any help is greatly appreciated.
Thanks in advance and best regards.
Chris
after spending almost 10h in trying to flash the E3372 into stickmode for proper support of AT-Commands, i just threw the towel (before almost all my hair has fallen out...) and wanted to try out the LTE-Stick in NDIS-Mode on the OPNSense.
Unfortunately the stick somehow is getting connected and disconnected over and over again, without holding that connection.
Here's my dmesg-output:
Quote
ue0: ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0 (disconnected)
<USB Ethernet> on cdce0
cdce0: at uhub1, port 4, addr 1 (disconnected)
ue0: Ethernet address: 00:1e:10:1f:xx:xx
cdce0: detached
usbd_req_re_enumerate: addr=1, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=1, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
usb_alloc_device: Failure selecting configuration index 0:USB_ERR_IOERROR, port 4, addr 1 (ignored)
ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0
ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0 (disconnected)
usbd_req_re_enumerate: addr=1, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
usb_alloc_device: Failure selecting configuration index 0:USB_ERR_IOERROR, port 4, addr 1 (ignored)
ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0
ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0 (disconnected)
usbd_req_re_enumerate: addr=1, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0
cdce0 on uhub1
cdce0: <CDC Ethernet Control Model ECM> on usbus0
ue0: ugen0.2: <HUAWEIMOBILE HUAWEIMOBILE> at usbus0 (disconnected)
<USB Ethernet> on cdce0
cdce0: at uhub1, port 4, addr 1 (disconnected)
ue0: Ethernet address: 00:1e:10:1f:xx:xx
cdce0: detached
The stick is directly connected with the APU2C4 via the BackUSB-Ports and as far as i've read on the documentation should be supported by the OS.
Is there any prior preparation to be done to support this stick properly, or what am i missing here?
I am planning to use this stick as LTE-Failover-Connection in case my main line is getting disconnected.
Any help is greatly appreciated.
Thanks in advance and best regards.
Chris