Messages

Code Select Expand

mkdir /mnt2
mount -t zfs fix/ROOT/default /mnt2
cd /mnt2
ls -l


Post the output of "zfs list" after importing, please.

Per the release notes there was no change to the nut package.  So what are you all even talking about? :P

The FreeBSD port/package was updated and now crashes.

Is there any fanless hardware that has no holes to let in air & to let out hot air?

APU? (outdated now) Protectli?

Look ma, no holes! :-)

Here for an interface with 6 defined rules the UI displays these 6 plus the 2 floating rules that also apply to this interface. The number shown in the selector is 6, the number of rules displayed is 8.

Works that way both without and with the patch.

Same for interface groups. The floating rules are always added to the display but do not change the number in the little circle in the selector.

See screenshots - 1 vs. 3 and 5 vs. 7. Makes sense to me - if that is intended and consistent.

"AI has absolutely reduced the cost of creating technical debt." -- ChatGPT

Stealing that! :-)

Da, back to workink.

Code Select Expand

[2355] pid 59276 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2365] pid 76306 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2375] pid 96545 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2383] pid 11941 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2385] pid 15230 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2395] pid 32978 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2403] pid 45958 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)
[2405] pid 50289 (upsc), jid 0, uid 0: exited on signal 11 (no core dump - bad address)

Interestingly the command does work, it only crashes on exit:

Code Select Expand

root@opnsense:~ # upsc ups
battery.charge: 100
battery.current: 0.90
battery.date: 07/20/2024
battery.runtime: 1560
battery.runtime.elapsed: 0
battery.voltage: 27.10
battery.voltage.nominal: 24
device.contact: hostmaster@hausen.com
device.description: UPS SNMP Card
[...]
ups.status: OL
ups.temperature: 34
ups.test.date: 05/09/2026
ups.test.result: Ok
Segmentation fault

Kind regards,
Patrick

why you dont recommend?

Because I think routing is superior to bridging in more or less every situation.

Are you running a transparent bridge setup? If yes you should have told from the beginning.

Sorry, no idea, I do not use that and do not recommend it.

LAN servers to Internet: LAN in and WAN out
Internet to LAN servers: WAN in and LAN out

In and out is always referring to the interface in question. Not our macroscopic view of "my private LANs are inside and the Internet is outside".

* output then appears to stop at:
amdtemp0: found 4 cores and 1 sensors

Possibly your imported configuration is simply not configured for serial console output? That's what would happen if that was the case.

I have for many many years ran 100% asic based soho hardware for home fw.

What exactly? Most SOHO products ship a more or less current and more or less competently hacked together Linux system. E.g. Fritzbox, which are exceptionally good at updates at least.

Ich habe das auch namentlich als PPPOEVLAN zugewiesen, das ist aber m.W. nicht notwendig.

Ist richtig, muss man nicht. Ich mache das z.B. nicht.