Messages

16

23.7 Legacy Series / Re: WAN not getting IPV6 address

« on: November 05, 2023, 03:38:34 am »

Even when using the same hardware, your DUID will change when installing OPNsense. If your ISP is picky about this, copying the DUID from pfSense might work.

Cheers
Maurice

And I have no good way to get the DUID from pfSense.  It is not stored in the backup config file.

17

23.7 Legacy Series / Re: WAN not getting IPV6 address

« on: November 04, 2023, 11:33:16 pm »

Hello,

I just came from pfSense, and configured my WAN interface the same way.  DHCP & DHCPv6 with a /56 prefix for IPv6.  However, no matter what I do unless I check "Request only an IPv6 prefix" I get no IPv6 information on the WAN.  Same NIC in my router, everything else is the same.  Even got the same IPv4 address.  Any suggestions on where to look and what you need to help me?

You had the same config at pfsense?
You are the dev who creates the script for transfer from pfsense to opnsense?

Sent from my SM-S918B using Tapatalk

Yes, I'm the one working on the program.  Settings should work fine but I get the following in my logs

Code: [Select]

2023-11-04T17:31:16-05:00 Notice dhcp6c reset a timer on igb0, state=SOLICIT, timeo=23, retrans=128544
2023-11-04T17:31:16-05:00 Notice dhcp6c send solicit to ff02::1:2%igb0
2023-11-04T17:31:16-05:00 Notice dhcp6c set IA_PD
2023-11-04T17:31:16-05:00 Notice dhcp6c set option request (len 4)
2023-11-04T17:31:16-05:00 Notice dhcp6c set elapsed time (len 2)
2023-11-04T17:31:16-05:00 Notice dhcp6c set identity association
2023-11-04T17:31:16-05:00 Notice dhcp6c set client ID (len 14)

18

23.7 Legacy Series / WAN not getting IPV6 address

« on: November 04, 2023, 10:24:13 pm »

Hello,

I just came from pfSense, and configured my WAN interface the same way.  DHCP & DHCPv6 with a /56 prefix for IPv6.  However, no matter what I do unless I check "Request only an IPv6 prefix" I get no IPv6 information on the WAN.  Same NIC in my router, everything else is the same.  Even got the same IPv4 address.  Any suggestions on where to look and what you need to help me?

19

General Discussion / Re: New user - Migrating from "The Other One - CE 2.7.0" to OPNsense

« on: November 03, 2023, 01:34:55 pm »

I wish I had seen this before I started my project to convert a pfSense config file to an OPNSense config file by writing a program.

https://github.com/smccloud/pfSense-to-OPNSense-Config-File-Converter

20

General Discussion / Problem connecting to Meraki Client VPN

« on: February 01, 2020, 09:06:12 pm »

Hello,

Where I work we use a Meraki MX64 firewall and our VPN access is through their client VPN.  Happens to be L2TP/IPSec.  It worked fine until I switched to OPNsense.  From what I can see nothing is being blocked (I did add a rule to allow anything from the public IP I connect to back into my firewall).

Nothing is being blocked outbound that I can see either.  Any suggestions on what to look at in order to get this working (other than deploying the OpenVPN appliance at work so I can connect using that instead).