Messages

181

21.7 Legacy Series / Re: using more then one core

« on: August 22, 2021, 03:52:57 pm »

Set this tunable and reboot: net.isr.maxthreads="-1"

182

21.7 Legacy Series / Re: Slow Recursion Time with Unbound

« on: August 21, 2021, 04:03:04 pm »

Have you tried running unbound with a higher log level than the default, and if that doesn't yield any clues, with query logging enabled?

My unbound used to be slow, and when running it with verbose logging, it appeared that it was timing out on IPv6 queries, as my internet connection currently doesn't support IPv6. It didn't show that with the default log level.

183

21.1 Legacy Series / Re: Problem connecting Apple Appstore

« on: August 15, 2021, 07:20:26 pm »

I’m seeing this too. I’m running Unbound with DoH to Cloudflare and Quad9, and I’m running Sensei as well. I’m on OPNsense 21.7.1 BTW, so it happens there as well.

184

21.7 Legacy Series / Re: Unbound won't start from GUI after 21.7.1 upgrade (from 21.7)

« on: August 07, 2021, 03:53:45 pm »

Have you checked if the system time is correct, and ntp sync is working properly? In another thread someone reported time deviations leading to instability.

185

21.7 Legacy Series / Re: Slow Download Speeds

« on: August 05, 2021, 07:42:06 am »

What kind of hardware are you running OPNsense on?

186

21.7 Legacy Series / Re: DNSBL cron job

« on: August 01, 2021, 06:19:30 pm »

I found unbound sometimes does restart on link up/down events, and perhaps also on DHCP renewal. Do these times coincide with other messages in the logs?

187

21.7 Legacy Series / Re: Can't get Internet access from 2nd LAN

« on: July 31, 2021, 08:09:04 pm »

If both LAN ports are in the same subnet, you can bridge the interfaces. Otherwise you need to enable that second LAN interface, give it an ip address in the correct range, and add appropriate access and routing.

188

21.7 Legacy Series / Re: Having problem installing the installer is not working

« on: July 31, 2021, 08:05:48 am »

I have seen this too, the ZFS installer doesn’t show any progress for the first minute or so, and longer on slower systems, giving the impression of a stall.
Both the UFS and ZFS install gave some text messages below in the screen.

189

21.7 Legacy Series / Re: 21.7 Boot hang at “Configuring VLAN interfaces...” with imported 21.1 config

« on: July 31, 2021, 06:37:27 am »

I’m not sure, unless they’ve replaced the package in the stock 21.7 repository, this would get you back the default 21.7 kernel with the bug still in it.

190

Zenarmor (Sensei) / Re: 21.7, disk errors, possibly related to iflib/netmap and igb driver

« on: July 30, 2021, 04:07:32 pm »

The new test kernel by Franco seems to work, I have been running OPNsense + Sensei in native netmap mode for a few hours, and no more ahci errors/timeouts. Thanks to all involved!

191

21.7 Legacy Series / Re: 21.7 Boot hang at “Configuring VLAN interfaces...” with imported 21.1 config

« on: July 30, 2021, 03:24:12 pm »

I was having the AHCI timeouts/errors, and with the new test kernel they seem to be gone. Uptime is now over an hour or so. Sensei running fine with native netmap driver.
Thanks to all involved in getting this fixed!

192

21.7 Legacy Series / Re: Qotom box: disk errors after upgrade to 21.7 - possibly network driver related?

« on: July 30, 2021, 05:45:49 am »

Thanks for the update on this!

193

Zenarmor (Sensei) / 21.7, disk errors, possibly related to iflib/netmap and igb driver

« on: July 29, 2021, 11:40:09 am »

I'm using a Qotom box (Q3xxG4-P, with the Intel 211 network card) for OPNsense which worked really well until the upgrade to 21.7. As soon as there is any load on the system, I start getting these disk errors (ahci CAM errors or timeouts).
So far I have tried changing the SSD for an A-brand one, and I have reinstalled the system from the ISO. Still no luck. I have tried to disable NCQ en trim, but this doesn't seem to be it.

Edit: now that I think of it, the errors always start happening after enabling Sensei. You see that debugging thingy about the network card being put in permanently promiscuous mode, and shortly after that, the system hangs. Could that have anything to do with this?

See also https://forum.opnsense.org/index.php?topic=24122.0

194

21.7 Legacy Series / Re: Qotom box: disk errors after upgrade to 21.7 - possibly Sensei related?

« on: July 29, 2021, 07:39:47 am »

Update: I have switched Sensei over from the native to the generic driver, and it seems to be working now. No more sata errors and timeouts. Fingers crossed...

Edit: spoke too soon, the errors returned.

195

21.7 Legacy Series / Qotom box: disk errors after upgrade to 21.7 - possibly network driver related?

« on: July 28, 2021, 09:55:31 pm »

I'm using a Qotom box (Q3xxG4-P, with the Intel 211 network card) for OPNsense which worked really well until the upgrade to 21.7. As soon as there is any load on the system, I start getting these ahci CAM errors or timeouts.
So far I have tried changing the SSD for an A-brand one, and I have reinstalled the system from the ISO. Still no luck.
I have tried to disable NCQ en trim, but this doesn't seem to be it.

Anything else to try? Has 21.7 seen updates in the storage / disk subsystem?

Edit: now that I think of it, the errors always start happening after enabling Sensei. You see that debugging thingy about the network card being put in permanently promiscuous mode, and shortly after that, the system hangs. Could that have anything to do with this?

Edit 2: Not using any VLANs here so I can’t comment on that.