Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - bulmaro

Pages: 1 2 [3] 4

Tutorials and FAQs / Re: HOWTO OPNsense in Microsoft Azure

« on: August 28, 2017, 11:43:57 pm »

Thanks Franco for the observation, I made small changes of your observation.
I think it's a good idea to move to the Tutorial section

Tutorials and FAQs / HOWTO OPNsense in Microsoft Azure

« on: August 28, 2017, 08:37:22 pm »

Sorry, I do not speak English, I try to translate the step I took, after reading several documents online
If someone can use the steps to configure your firewall in Microsoft Azure

FreeBSD Azure
1- Create MV FreeBSD 11.0    https://docs.microsoft.com/en-us/azure/virtual-machines/windows/classic/tutorial

2- Create another additional network interface      https://docs.microsoft.com/en-us/azure/virtual-network/virtual-network-network-interface

3- Attach the NIC to a VM   https://www.petri.com/add-network-interface-azure-vm

4- Connect with ssh MV
Before we have to enable the root user by ssh
$ sudo vi / etc / ssh / sshd_config
Locate the following line that is disabled
#PermitRootLogin on

Uncomment the line and change it in yes
PermitRootLogin yes
$ sudo /etc/rc.d/sshd restart
$ sudo passwd root
Changing local password for root
New Password:
Retype New Password:

5- Follow the next steps on the page   https://github.com/opnsense/update#
$ sudo pkg install ca_root_nss
$ sudo fetch https://raw.githubusercontent.com/opnsense/update/master/bootstrap/opnsense-bootstrap.sh

Connect with WinSCP Transfer Attachment file configure.xml
Edit the opnsense-bootstrap.sh file and comment the line
$ sudo vi opnsense-bootstrap.sh
   #reboot
$ sudo sh ./opnsense-bootstrap.sh

Before the MV restarts you must do this step, otherwise you will not have access to the MV
Open another end with the root user and copy the file
#cp config.xml /usr/local/etc/config.xml
After a successful restart, OPNsense should be up and running, Can improve the configuration to your liking
Connect via web interface https://<ip>/

6- Portal Azure Configure Route Table   https://campus.barracuda.com/product/nextgenfirewallf/article/NGF62/AzureARMUDRWebPortal/
Rute table does operation NAT and redirection traffic the OPNsense

If there is anything else to improve, please suggest

Thanks OPNsense Teams, that's what I can contribute

17.7 Legacy Series / Re: Dynamic DNS (NO-IP)

« on: August 24, 2017, 04:16:11 pm »

Thank you very much for the help, I'm solved

# chown noip:noip /usr/local/etc/no-ip2.conf
# echo 'noip_enable="YES"' >> /etc/rc.conf

17.7 Legacy Series / Dynamic DNS (NO-IP)

« on: August 21, 2017, 04:10:32 pm »

Hi friends forum
Dynamics dns with no-ip service, does not update ip public.
Installing this manual package updates ip public
pkg.freebsd.org/FreeBSD:11:amd64/latest/All/noip-2.1.9_4.txz
After a reboot of the system how to enable the load at startup?
Some of you have had this problem, that can give me some idea.

17.7 Legacy Series / Re: Multi WAN 17.7 Free box release

« on: August 01, 2017, 03:43:51 pm »

Quote from: franco on August 01, 2017, 10:44:41 am

Hi Julien,

It's "Free Fox". Forgive me for asking for more context: which Multi-WAN issue are you referring to and (a) was it always not working or (b) started to stop working at a particular version?

Cheers,
Franco

Update version 17.7 and I have problem with multiwan detect the following.
In the gateways, when IP Monitor is left in offline status the second interface, if Disable Gateway Monitoring is enabled in enline.
Any ideas?
Thank you for your attention

General Discussion / Re: Port Forwarding on Azure

« on: June 21, 2017, 06:48:38 pm »

Hello Friend
Some howto to guide me to do the installation, I want to mount my firewall in azure
Thank you for your attention.

17.1 Legacy Series / Re: Packet Loss with IPS

« on: May 07, 2017, 12:44:41 am »

I have 4 network interface, I happen with a network interface Packetloss 46%

17.1 Legacy Series / Re: 17.1.5 - Gateway problems

« on: April 27, 2017, 08:04:52 pm »

Gooday to everyone
My problem is the following
My pc is connected to the LAN2 of the internet WAN3, to get maximum traffic in the LAN2, the Internet is disconnected from the pc connected in the network LAN1

I attached the image and the configuration of my opnsense.
I thank you for the attention and help to correct my problem in what I am doing wrong

17.1 Legacy Series / Re: Error fatal trap

« on: March 09, 2017, 08:25:41 pm »

Thank you very much, problem solved

17.1 Legacy Series / [SOLVED] Error fatal trap

« on: March 08, 2017, 08:26:26 pm »

Hello everyone
Can someone have any idea about this error message from the attached image?
It is three times that I get this message, until I must enter the reboot command to start normamal.

Reviewing the message log
NetFlow is not working for me

flowd_aggregate.py: flowd aggregate died with message Traceback (most recent call last): File "/usr/local/opnsense/scripts/netflow/flowd_aggregate.py", line 148, in run aggregate_flowd(do_vacuum) File "/usr/local/opnsense/scripts/netflow/flowd_aggregate.py", line 85, in aggregate_flowd stream_agg_object.cleanup(do_vacuum) File "/usr/local/opnsense/scripts/netflow/lib/aggregate.py", line 281, in cleanup self._update_cur.execute('vacuum') DatabaseError: database disk image is malformed

Thanks for your attention

17.1 Legacy Series / Re: [Solved] Multi WAN Problem

« on: February 13, 2017, 04:46:42 pm »

Add the following configuration, did no effect

17.1 Legacy Series / Re: Multi WAN Problem

« on: February 10, 2017, 05:10:32 pm »

Quote from: franco on February 09, 2017, 08:03:05 pm

On 17.1.1 try setting the sysctl for the old routing behaviour:

# sysctl net.pf.share_forward=0

If the problem persists, was it verified and working on a 16.7.14? If not, it could be a setup issue.

Cheers,
Franco

It is actually solved, but when the restart is erased the configuration, how to leave it permantente?
Thank you for your attention