1936
General Discussion / Re: Fresh install, cant ping LAN interface
« on: September 20, 2016, 08:15:13 am »
Does the web interface open in the browser?
Bart...
Bart...
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
1937
16.7 Legacy Series / Re: OpenVPN client: route everything through VPN fails
« on: September 17, 2016, 05:55:24 pm »
Try it, who cares if it is not correct 
You need to see if routing is the issue. The guides are written from the point of view that the VPN tunnel is used as a site-to-site connection that grants access to a limited set of networks at the far end (a.k.a. split tunnelling).
I think you are configuring the tunnel to take all your WAN traffic to a remote internet connection. Valid, but not typical.
If you do identify your issue as routing, you can then set up additional configuration to ensure that your default gateway survives a reboot. E.g. change the default gateway through a OpenVPN post-connection script and set OPNsense to allow default gateway switching.
Bart...
You need to see if routing is the issue. The guides are written from the point of view that the VPN tunnel is used as a site-to-site connection that grants access to a limited set of networks at the far end (a.k.a. split tunnelling).
I think you are configuring the tunnel to take all your WAN traffic to a remote internet connection. Valid, but not typical.
If you do identify your issue as routing, you can then set up additional configuration to ensure that your default gateway survives a reboot. E.g. change the default gateway through a OpenVPN post-connection script and set OPNsense to allow default gateway switching.
Bart...
1938
16.7 Legacy Series / Re: OpenVPN client: route everything through VPN fails
« on: September 17, 2016, 10:44:36 am »
Your default gateway is set to your WAN IP, not to your tunnel IP.
Try this in the console:
route add default 10.4.28.95
Change the default gateway in OPNsense if this fixes the problem
Bart...
Try this in the console:
route add default 10.4.28.95
Change the default gateway in OPNsense if this fixes the problem
Bart...
1939
16.7 Legacy Series / Re: OpenVPN client: route everything through VPN fails
« on: September 16, 2016, 11:17:36 pm »
what is the output from netstat -r in the OPNsense shell?
Bart...
Bart...
1940
16.7 Legacy Series / Re: Port 0 and 597 showing 'open'.
« on: September 15, 2016, 06:58:56 pm »
Checked with GRC Shields Up and found only the ports I've opened
Bart...
Bart...
1941
16.7 Legacy Series / Re: IPv6: Access via browser not possible, ping6 and telnet are working
« on: September 14, 2016, 08:25:29 am »
If your ISP doesn't provide native IPv6, it may be worthwhile trying a tunnel directly from OPNsense: https://docs.opnsense.org/manual/how-tos/ipv6_tunnelbroker.html
Bart...
Bart...
1942
16.7 Legacy Series / Re: LAN goes down even on minor configuration changes
« on: September 12, 2016, 07:09:00 pm »1943
Hardware and Performance / Re: New Mini PC Hardware
« on: September 11, 2016, 12:36:49 pm »
I'd prefer a Braswell equivalent for crypto offload. The Bay Trail CPU's don't do AES-NI.
Bart...
Bart...
1944
General Discussion / Re: Installation Media Creation
« on: September 05, 2016, 06:34:04 pm »
Are you using the VGA image? Also check this thread for pointers: https://forum.opnsense.org/index.php?topic=3622.0
Bart...
Bart...
1945
General Discussion / Re: SNMP, router status updates available
« on: September 05, 2016, 06:32:01 pm »
Hi Maarten,
I've written a Python script to email when updates are available: https://forum.opnsense.org/index.php?topic=2032.0
Bart...
I've written a Python script to email when updates are available: https://forum.opnsense.org/index.php?topic=2032.0
Bart...
1946
16.7 Legacy Series / Re: 6rd Configuration
« on: September 04, 2016, 05:28:30 pm »
Can you ping 2a00:1450:4001:816::2003 from the OPNsense console? (option 7)
Bart...
Bart...
1947
16.7 Legacy Series / Re: No Internet on VPN
« on: August 29, 2016, 08:16:42 am »
Hi Julien,
Yes, and the routing table after connection to the VPN. From a terminal run netstat -rn -f inet
Bart...
Yes, and the routing table after connection to the VPN. From a terminal run netstat -rn -f inet
Bart...
1948
16.7 Legacy Series / Re: Need immediate assistance! WAN not coming up in vitualized OPNsense firewall.
« on: August 27, 2016, 10:26:43 am »
Hi Bobby,
Please give more details of your setup. Why do you have a bridge? What type of WAN connection do you have? (PPPoE, DHCP, Static).
Have you tried a fresh OPNsense on a different VM?
Bart...
Please give more details of your setup. Why do you have a bridge? What type of WAN connection do you have? (PPPoE, DHCP, Static).
Have you tried a fresh OPNsense on a different VM?
Bart...
1949
Hardware and Performance / Re: OPNsense on old Riverbed Steelhead 250
« on: August 22, 2016, 06:09:48 pm »
Use another system to install OPNsense on a flash drive and use that instead of the 2GB drive.
Bart...
Bart...
1950
16.7 Legacy Series / Re: not getting IP via DHCP on WAN
« on: August 14, 2016, 12:19:57 pm »
I would:
Try with IPv6 disabled to exclude that as an influence.
Run tcpdump on the OPNsense WAN interface and look at the traces with Wireshark to see if where the DHCP protocol fails.
Try a different NIC. I had issues with an Intel on the WAN and ended up with a Realtek. YMMV.
Bart...
Try with IPv6 disabled to exclude that as an influence.
Run tcpdump on the OPNsense WAN interface and look at the traces with Wireshark to see if where the DHCP protocol fails.
Try a different NIC. I had issues with an Intel on the WAN and ended up with a Realtek. YMMV.
Bart...