Messages

1

General Discussion / Install OPNsense on Netgear ProSafe

« on: September 29, 2015, 07:32:13 pm »

Hey Everyone,

Going to received a Netgear ProSafe 6 (FVS336G-300NAS) and was wonder if you can install/flash OpnSense onto this device. I have only install and configured OPNsense on a rack mount server but never on  Embedded Firewall before. Dose anyone have any suggestion, or had any success getting OPNsense onto this device.

Best Regards,

LordD1

2

General Discussion / Re: 1000 Forum Members!

« on: July 02, 2015, 04:21:05 pm »

Because OPNsense rocks!!!
I bet this really going get a lot of people taking a second look at us now.

3

General Discussion / Re: Openvpn Can't access Clients in my Network over VPN

« on: June 23, 2015, 05:31:16 pm »

Hello


So for your IPV4 Tunnel Network it just have to IP that would be giving to the VPN users. (ex 192.168.15.0/24)
From there you can go to the advance option and push route's to the networks that you want the vpn user to have access too.

Ex
p.ush "route 192.168.1.0 255.255.255.0"
push "route 192.168.2.0 255.255.255.0"

Not sure about setting for DNS server and Netbios as I didn't need it for my set-ups.

Best Regards,

LordD

4

General Discussion / Re: is it right?

« on: May 20, 2015, 11:15:33 pm »

Hey Kaxia,

You should set it to any and that will work fine. I have it set up on mines that way with no issue.

Best Regards,

LordD

5

General Discussion / Re: Opt1 wireless guest no connectivity

« on: May 19, 2015, 09:08:42 pm »

Hello,

For your firewall rules what happens whe you change your destination to any or Wan net. Are you able to reach the Internet then.

6

General Discussion / Re: Opt1 wireless guest no connectivity

« on: May 19, 2015, 03:41:34 pm »

Hey ahmy,

Might need some more information in order to solve this issue.
1. When you connect to the device are you getting an IP address.
2. If so are you able to ping the gate way from your wireless device .(ex. ping 10.0.0.1)
3. Next confirm that opt1 interface can reach the the internet.  Go under Diagnostics and select ping, From ther put the following.
Host : 8.8.8.8
IP Protocol : IPv4
Source Address opt1
Count: 3
Please paste the results on your next update.

7

General Discussion / Re: [SOLVED] Standard user are unable to see web content after update.

« on: April 19, 2015, 03:18:31 am »

Thanks guys,

Just updated and everything looks good on my end as well.

8

General Discussion / Re: [SOLVED] Standard user are unable to see web content after update.

« on: April 15, 2015, 05:25:42 am »

Hello,

I also performed the update as well and still see the error message. Created a test user and performed the code on the firewall. Wasn't able to get the results like AdSchellevis mention. Below is the results I got.

 

Code: [Select]

php /tmp/test.php

Notice: Undefined index: authmode in /usr/local/etc/inc/priv.inc on line 229

Notice: Undefined index: authserver in /usr/local/etc/inc/auth.inc on line 1248

Notice: Undefined index: priv in /usr/local/etc/inc/priv.inc on line 203

Notice: Undefined index: member in /usr/local/etc/inc/auth.inc on line 539
Array
(
)

Best Regards,

LordD

9

General Discussion / [SOLVED] Standard user are unable to see web content after update.

« on: April 13, 2015, 09:00:19 pm »

Hello

After performing 15.1.9-amd64 update I starting seeing 201 error when I log in. This seems to happen any user expect the root user. The user the is set up under the admin group and never had a issue until after the llatest update.
Attempted to create a new account with the same admin credential and also performed a reboot(you never know).
But still received the same 201 error "No page assigned to this user! Click here to logout.". Any suggestion will be very appreciated.

Best Regards

LordD1

10

15.1 Legacy Series / Re: Uable to add a new alias.

« on: March 30, 2015, 03:21:37 am »

Update,

Just upgraded to 1.57.2 and everything works like a charm. After the upgrade I attempt to add a new alias. It now show up as soon as it is created. Will keep testing and report any bugs, but other than that loving the work that is being done with OPNsense.

Best Regards,

LordD1

11

15.1 Legacy Series / [SOLVED] Uable to add a new alias.

« on: March 29, 2015, 09:26:35 pm »

Hello,

Just installed OPNsense 15.1.8-07aaac43d and having issue with the alias section.
Every time I attempt to create a new alias and save it, nothing shows up on my list. Also made sure that apply changes was press after create it, but still wasn't able to see the it created. Is there a bug on this version, any help would be very appreciated.

Thanks

LordD
Modify message