Messages

1

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: August 30, 2024, 12:37:06 pm »

Did some edits to my plan, I'm going to use vlan1 for lan e vlan2 (0.2) for guests, it was to difficult with the other setup and with my current hardware, now I need an advice, two vlans or 1 for guests and no vlan for lan?
is any different? keep in mind that vlan1 untagged is necessary for unifi, so I thought:
vlan1 (opnsense default? untagged?) for lan
vlan2 (tagged for unifi)
correct?

2

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 09, 2024, 02:54:53 pm »

applied a modification for ipcam vlan20 untagged and configured the switch:

Code: [Select]

Port 1: AP1 vlan1 untagged, vlan20-30-40 tagged
Port 2: AP2 vlan1 untagged, vlan20-30-40 tagged
Port 3: Reolink vlan20 untagged
Port 4: Empty, vlan1 untagged (I know it isn't secure but is at home)
Port 5: Router, vlan1-20 untagged
Port 6: Router, vlan20-30-40 taggedSwitch config:

If it is all okay I will start to configure opnsense

3

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 05, 2024, 03:11:53 pm »

no indeed, I will put vlan20 untagged

4

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 04, 2024, 05:57:29 pm »

yes, perfect, I'll try

5

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 04, 2024, 05:16:40 pm »

could this config work? I want 3 ssid: iot, clients and guests

Switch:
Port 1: AP1 vlan1 untagged, vlan20-30-40 tagged
Port 2: AP2 vlan1 untagged, vlan20-30-40 tagged
Port 3: Reolink IPCAM vlan20 tagged
Port 4: Empty
Port 5: Router, vlan1 untagged
Port 6: Router, vlan20-30-40 tagged

6

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 04, 2024, 12:45:41 am »

Too much for me now ahahh, I need to understand opnsense better
I have a question, unifi does need untagged only for management and then it uses tagged to transfer traffic?
or it use only untagged? so I can use lower speed port and don't waste faster ports

7

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 04, 2024, 12:37:22 am »

Seems perfect, now I'll try to set it up
I'll probably ask you more haha
Thank you for the great help you are giving me (and for your patience haha)

8

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 03, 2024, 11:50:58 pm »

Sadly my APs are Unifi, so I need it, it seems 
I evidently didn't do the proper research before buying switch and router
Now with that in mind, how do I tell OPNsense to pass untagged traffic on that particular port?
Sorry but this is the first time I've attempted to set up a network with different VLANs in practice, I only knew the theory

9

24.1 Legacy Series / Re: VLAN bridging and use them on different ports

« on: July 03, 2024, 06:10:31 pm »

could I use only one cable to the switch? or I need one to separate tagged and untagged?
It's quite a headache ahah

10

24.1 Legacy Series / VLAN bridging and use them on different ports

« on: June 28, 2024, 03:06:40 pm »

I'm writing to you here as a continuation of this post: https://forum.opnsense.org/index.php?topic=29436.0
I wanted to ask you, what should I put as the parent interface of the VLANs if I want to use a LAN bridge?
I have a Qotom Q20332G9-S10 with lots of ports as you can see, I want to use 1x10gb sfp for my managed poe switch to link 2 APs and some cameras, and then I wanted to use some 2.5gb from the qotom to my server and pc
I wanted to configure these VLANs:

Code: [Select]

VLAN 1 (Management)
Gateway: 192.168.1.1
Switch: 192.168.1.2
AP1: 192.168.1.3 connected to switch 2.5gb poe
AP2: 192.168.1.4 connected to switch 2.5gb poe
unRAID: 192.168.1.5 connected to qotom 2.5gb

VLAN 10 (DMZ, Docker) https://forums.unraid.net/topic/62107-network-isolation-in-unraid-64/
Gateway: 192.168.10.1

VLAN 20 (IOT)
Gateway: 192.168.20.1

VLAN 30 (Clients)
Gateway: 192.168.30.1
My-PC: connected to qotom 2.5gb
Parents-PC: connected to qotom 2.5gb

VLAN 40 (Guests)
Gateway: 192.168.40.1I know that switching with the router isn't the best thing, but I have limited money and a lots of ports on the router, so I'm gonna use them
Do you have any suggestions? I'm going crazy

11

Italian - Italiano / Re: Ottimizzazione PPPoE WAN per FTTH 2.5gbps

« on: June 28, 2024, 03:00:54 pm »

Scusa il ritardo, avevo lo stesso problema con la stessa configurazione, bisogna semplicemente attivare il multicore/multithread nei tunables:

Code: [Select]

net.isr.dispatch=deferred
net.isr.maxthreads=-1