1
23.1 Legacy Series / Re: OpnSense keeps crashing(Version 23.1.11 f1305748e)
« on: July 25, 2023, 02:47:30 am »
Was a RAM issue. Been running for a week without fail 
. Thanks everyone!
. Thanks everyone!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
23.1 Legacy Series / Re: OpnSense keeps crashing(Version 23.1.11 f1305748e)
« on: July 10, 2023, 05:14:10 am »
Thanks for the thoughts and recommendations everyone. I am returning the RAM, as its covered by amazon(thanks Bezos). In terms of the N200, that's disappointing to hear the stability problems. I will try that command that was recommended, and hope for the best. Once again, thanks everyone, and I will reply to this thread once I get my new RAM, with hopefully good news!
3
23.1 Legacy Series / Re: OpnSense keeps crashing(Version 23.1.11 f1305748e)
« on: July 09, 2023, 12:13:49 am »
Ran memtest86+ for 41:09 minutes and it detected 19 errors and 1 pass. I assume that means the memory's bad. memtest86+ recommends swapping one of the modules, but this is a one dimm system. I just got the ram, so should I just return in and replace it with a new one to be safe?
4
23.1 Legacy Series / Re: OpnSense keeps crashing(Version 23.1.11 f1305748e)
« on: July 08, 2023, 09:53:39 pm »
Downloading memtest86+
just for specs, im running and N200 with a 1x 16gb ddr5 4800mhz with a kingston 500gb ssd.
To note for the install of opnsense: When I was installing, I was trying to use the zfs version, but it kept failing, so i tried a few times and each time it would progress farther and then it finally worked. At the time, I just assumed it fixed whatever the issue was, but could that be the root of my problem?
just for specs, im running and N200 with a 1x 16gb ddr5 4800mhz with a kingston 500gb ssd.
To note for the install of opnsense: When I was installing, I was trying to use the zfs version, but it kept failing, so i tried a few times and each time it would progress farther and then it finally worked. At the time, I just assumed it fixed whatever the issue was, but could that be the root of my problem?
5
23.1 Legacy Series / Re: OpnSense keeps crashing(Version 23.1.11 f1305748e)
« on: July 08, 2023, 07:32:53 pm »Code: [Select]
trap number = 12
panic: page fault
cpuid = 0
time = 1688812201
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xfffffe00c5cd1b20
vpanic() at vpanic+0x17f/frame 0xfffffe00c5cd1b70
panic() at panic+0x43/frame 0xfffffe00c5cd1bd0
trap_fatal() at trap_fatal+0x385/frame 0xfffffe00c5cd1c30
trap_pfault() at trap_pfault+0x4f/frame 0xfffffe00c5cd1c90
calltrap() at calltrap+0x8/frame 0xfffffe00c5cd1c90
--- trap 0xc, rip = 0xffffffff82f1f043, rsp = 0xfffffe00c5cd1d60, rbp = 0xfffffe00c5cd1da0 ---
ng_netflow_expire() at ng_netflow_expire+0x273/frame 0xfffffe00c5cd1da0
softclock_call_cc() at softclock_call_cc+0x13d/frame 0xfffffe00c5cd1e40
softclock() at softclock+0x79/frame 0xfffffe00c5cd1e60
ithread_loop() at ithread_loop+0x25a/frame 0xfffffe00c5cd1ef0
fork_exit() at fork_exit+0x7e/frame 0xfffffe00c5cd1f30
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe00c5cd1f30
--- trap 0x80d08f20, rip = 0xffffffff80c30e5f, rsp = 0, rbp = 0x2b56000 ---
mi_startup() at mi_startup+0xdf/frame 0x2b56000
KDB: enter: panicHeres the part of the code,so you dont have to download that file
6
23.1 Legacy Series / OpnSense keeps crashing(Version 23.1.11 f1305748e)
« on: July 08, 2023, 07:31:54 pm »
Hello, I just setup my OPNSense router yesterday, so a fresh install and only a theme plugin. For some reason, the router keeps crashing. Every time I check the crash reporter(its huge btw), I see something related to the attached messages on there. I am new to networking and this whole system, so any advice or anything else you guys might need to help me, feel free to ask and I will try my best to help
Pages: [1]