Messages

1

Italian - Italiano / Firewall hardware e connessione FTTH da 10Gb/s

« on: May 24, 2023, 06:43:54 pm »

Ciao


Vorrei acquistare un Firewall hardware con l'ultima versione di OPNsense da connettere direttamente ad un ONT esterno che controlla una connessione FTTH da 10Gb/s.


Questo firewall dovrebbe gestire una LAN di 10 computer, un NAS e quattro TV connessi ad uno switch di 20 porte.


Siccome faccio un uso inteso di programmi di File sharing e di servizi di streaming su più dispositivi contemporaneamente, tale firewall dovrebbe essere in grado di in fare ciò senza problemi 24h/24 e 7g/7.


Quindi, quale firewall mi consigliate?


Grazie


Ciao

2

General Discussion / Re: Rules for use Torrent service

« on: January 14, 2019, 06:58:47 pm »

Enable bridge mode in your router/modem configuration. If it doesn't offer it, look for one that does (e.g. https://www.draytek.co.uk/products/business/vigor-130)

Bart...

Sorry but my router is already in Bridged mode also because I use the PPPoE protocol of the firewall to use the Internet. So, my firewall hardware knows my public dynamic IP and the various DNS used by my provider.

So, how do I set OPNSense to do what I want to do?

Thanks

Bye

3

General Discussion / Re: Rules for use Torrent service

« on: January 14, 2019, 05:52:48 pm »

How do I enable the OPNSense NAT to make the dynamic IP, provided by my ISP, routable for the LAN? In other words, I would like to disable the NAT of the VDSL2 router using this Internet service with the computers on the LAN.

Thanks

Bye

4

General Discussion / Re: Rules for use Torrent service

« on: January 12, 2019, 08:48:14 am »

Anybody still want to help me?

Thanks

Bye

5

General Discussion / Re: Rules for use Torrent service

« on: January 09, 2019, 06:23:34 pm »

There is no firewall enabled on the LAN computers.

The VDSL2 router should be set up correctly in Bridge mode because, a few months ago, I had a firewall hardware with pfSense and I did not have this problem. How come?

One thing I never understood: If I turn off NAT on the router, I can no longer access the Internet from the LAN computers. This happens with the old and the new firewall hardware. How come?

With OPNSense, is it possible to configure it so that it also acts as a full NAT for the entire LAN so that I can completely disable the router's firewall?

Thanks

Bye

6

General Discussion / Re: Rules for use Torrent service

« on: January 08, 2019, 05:22:10 pm »

So, how do I open the ports? In other words, why doesn't my NAT rule, which should open the Torrent port, work?

Thanks

Bye

7

General Discussion / Re: Rules for use Torrent service

« on: January 07, 2019, 07:09:22 pm »

Now, no error appears but, when I check the port, the Internet service indicates that its status is closed. How come?


Thanks


Bye

8

General Discussion / Re: Rules for use Torrent service

« on: January 07, 2019, 05:32:41 pm »

Help!!!

9

General Discussion / Re: Rules for use Torrent service

« on: January 07, 2019, 10:24:14 am »

I have noticed that, when I create and apply the Torrent rule, an error appears (see attachment). Where am I wrong?

Thanks


Bye

10

General Discussion / Re: Rules for use Torrent service

« on: January 06, 2019, 10:39:32 am »

Can you help me solve this problem?

Thanks

Bye

11

General Discussion / Re: Rules for use Torrent service

« on: January 04, 2019, 10:04:51 am »

Anybody understand what I'm doing wrong?

Thanks

Bye

12

General Discussion / Re: Rules for use Torrent service

« on: January 02, 2019, 09:16:17 am »

This is my current configuration:












The next two images represent the various port blocks:




How come? Is this normal?

While these images show the block of port 36603 analyzed by the service https://www.grc.com that reports the status Stealth on this port:




So, how do I remove all these blocks so that I can use the Torrent network without any problems?

Thanks

Bye

13

General Discussion / Re: Rules for use Torrent service

« on: December 30, 2018, 11:20:18 am »

In OPNsense, how do I analyze the firewall traffic to understand which packets pass and which not?

Thanks

Bye

14

General Discussion / Re: Rules for use Torrent service

« on: December 27, 2018, 12:32:17 pm »

How do I view all packets blocked by NAT?

NAT cannot block, it is NOT A FIREWALL. It just looks like one because the packets won't find the real destination.

How do I find out where these packages end up?

Thanks

Bye

15

General Discussion / Re: Rules for use Torrent service

« on: December 27, 2018, 12:02:33 pm »

I reset the firewall and configured it in a standard mode with the PPPoE protocol but my problem remained.

How do I view all packets blocked by NAT?

Thanks

Bye