Messages

1

18.1 Legacy Series / Re: NAT, port aliases, redirect not working after upgrade

« on: January 30, 2018, 09:52:14 pm »

I also installed an older version, got my opnsense working again and waiting for more confirmation before I switch again. Thanks a lot!
Stefan

2

18.1 Legacy Series / Re: NAT, port aliases, redirect not working after upgrade

« on: January 30, 2018, 05:31:00 pm »

Well actually the upgrade did not work for me .... So I reinstalled and imported the config .... but sill the same with the aliases

3

German - Deutsch / Re: Probleme mit NAT nach Installation von 18.1

« on: January 30, 2018, 12:40:01 pm »

Hab genau dasselbe Problem, scheint beim Iterieren über den Port-Alias ein Problem zu geben.
Ich habe dazu einen Thread im englisch sprachigen Forum eröffnet: https://forum.opnsense.org/index.php?topic=7078.0

Dort wird schon ein Patch erwähnt.

4

18.1 Legacy Series / NAT, port aliases, redirect not working after upgrade

« on: January 30, 2018, 12:36:46 pm »

Hi all, after upgrading to version 18.1, none of my port forwarding based on port aliases works. looking at /temp/rules.debug I just found following

......
UnifiPorts = "{ 8080 8443 8880 8843 27117 3478 }"
table <UNIFISERVER> persist
UNIFISERVER = "<UNIFISERVER>"
......

which seems ok, but

......
rdr on igb0 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1_vlan10 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb2_vlan3 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1_vlan1003 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb2_vlan1007 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1_vlan1005 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on ovpnc2 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on openvpn inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb2_vlan8 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb0_vlan101 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1_vlan10 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb2_vlan3 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1_vlan1003 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb2_vlan1007 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb1_vlan1005 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on ovpnc2 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on openvpn inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080
rdr on igb2_vlan8 inet proto {tcp udp} from {any} to {(self)} port $UnifiPorts -> $UNIFISERVER port 8080

......

the rules for redirecting just resolve to the first port in the alias

What can I do ? in the 17 branch everything worked .... Is there a fix ? I have lots of those definitions in my rules. O do I have to revert to the 17 branch ? If, how is it done ?
This way I rendered mi production setup unusable  ;-(

Thanks a lot
Stefan