Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - agustinrojen

#1
Hey guys! Im planning to use Captive Portal for the use of.

Allowing only listed MAC addresses to obtain IP address, connect to the internet, and to give a specific bandwidth to the specific IP address.

But. I'm really stuck on where to start/begin? Please help me and give me some hints and suggestions. Thank you!
#2
Can you give.me advices or suggestions on what to do or what to use to limit bandwidth of a specific MAC address? Thank you!
#3
Problem solved with Family Protection ADGuard! Thank you.
#4
Sir fabian. I followed the webproxyfilter. Nothing changes. I can still open adult sites
#5
Can I have advice or suggestion to block adult sites on my LAN Opnsense?
#6
Uhm mr. Hutiucip. I followed all ur instructions. and i succesfully entered my opnsense web GUI using the lan default 192.168.1.1 using my switch and client unit even though my WAN is 192.168.254.100 via dhcp.

But the problem now is. I can access.my opnsense web gui using my.clients. but my clients doesnt have internet.connection. what does that mean? Am i going to.configure something on opnsense. To have internrt connectoon in my clients?
#7
Excuse me. The internet and Modem in my situation is one.

Its a LTE modem that has a wifi and lan built to it and supplied internet by sim card. Default gateway is 192.168.254.254

It has 4 ports LAN ports.

LAN1 -- LAN2 -- LAN3 --LAN/WAN

Where should I connect it? From modem to opnsense.
#9
I got it from. MODEM(Internet) to OPNSense(WAN DHCP)
It is WAN 192.168.254.102 via DHCP and I got replies from websites when i pinged them.

But. I really dont have idea on what you said. OPNSense(LAN Static) to switch. What IP do i need to put on my static LAN? Gateway and DNS'S?
#10
Because I wil be using a wired NIC for my WAN. How can i access web GUI then?
#11
But. How can i access my Web GUI if.my.first wired nic will be WAN?
#12
What do I need to do sir? I cant understand it :(

Heres my diagram to follow.
#13
Im sorry sir. I think I've explained my setup wrong and in the other way. Please read this again. It's just a vice versa.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4:/DHCP4: 192.168.254.101/24
WAN(ue0) -> v4/DHCP4:

As you can see. Instead of using wireless driver NIC for my WAN. I used my second wired NIC as indicated below for my WAN interface.

I got 192.168.254.101/24 on my LAN interface because it was set into DHCP.

I just recently configured my DHCP server for LAN interface. But before I can configure dhcp server. I must make my LAN interface into a static form right?

So I change my LAN interface into static.

LAN (re0) -> v4:: 192.168.254.1/24
WAN(ue0) -> v4/DHCP4:

Then. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

Then. I've already change my LAN IP into static. I just finished configuring my DHCP server for my LAN interface. But. How can I give my WAN an IP address(internet connection from my DHCP server). How can I give IP address or internet connection to my clients if my WAN interface doesn't have one. My WAN interface is set to DHCP4. I thought it will have an IP coming from my LAN DHCP. Am I wrong? Please help me.

So it'll be. MODEM -> OPNSense (LAN Static) DHCP Server -> OPNSense(WAN DHCP4) -> SWITCH -> CLIENTS

Thank you again!

From Philippines.
#14
As seen in the image attached below. That will be my setup.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4: 192.168.1.1/24 (default. never changed after installation.
WAN(ue0) -> v4/DHCP4: 192.168.254.101/24

As you can see. Instead of using wireless driver NIC for my WAN. I used my first wired NIC as indicated below for my WAN interface, from Modem to OPNSense. That is why I got 192.168.254.101/24

So. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

and my question is..

How do I set up OPNSense to give clients IP address, Gateways, and DNS? for internet connection.
As indicated below. I will be using my second wired NIC from OPNsense to my Switch and my Switch to the Clients.

Can someone help me with my problem? Btw. I'm a newbie when it comes network security. So, it'll be much appreciated if you gentlemen/women could help me. Thank you! I'll be waiting for your thoughtful replies.  :)

From Philippines.
#15
As seen in the image attached below. That will be my setup.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4: 192.168.1.1/24 (default. never changed after installation.
WAN(ue0) -> v4/DHCP4: 192.168.254.101/24

As you can see. Instead of using wireless driver NIC for my WAN. I used my first wired NIC as indicated below for my WAN interface, from Modem to OPNSense. That is why I got 192.168.254.101/24

So. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

and my question is..

How do I set up OPNSense to give clients IP address, Gateways, and DNS? for internet connection.
As indicated below. I will be using my second wired NIC from OPNsense to my Switch and my Switch to the Clients.

Can someone help me with my problem? Btw. I'm a newbie when it comes network security. So, it'll be much appreciated if you gentlemen/women could help me. Thank you! I'll be waiting for your thoughtful replies.  :)

From Philippines.