Messages

1

General Discussion / Re: Dynamic routing config

« on: January 29, 2019, 03:40:01 pm »

We need to migrate our config from Mikrotik. Last time I guess we had an issue with the IPs - we need to set up some 5-6 IPv4 subnets. Perhaps I could PM you read access to our Mikrotik because otherwise it's pretty hard to explain everything?   

2

General Discussion / Dynamic routing config

« on: January 29, 2019, 10:44:45 am »

So after a year or so I'm finally ready for the 2nd attempt to set up OPNsense (first one failed miserably).  I see many thing have changed for the better which is great. I wonder if someone here can help me with the dynamic routing config of my OPNsense router? I'm ready to donate or pay for services. Please PM me or post a reply to this thread. Thanks in advance.   

3

General Discussion / Looking for a freelancer to assist with OPNsense setup

« on: December 16, 2017, 12:05:05 am »

Hi,

So basically what the subj says looking for help with router config/setup: dynamic routing (BGP), two incoming and two outgoing interfaces, multiple IPv4 subnets on every interface.

Guys please feel free reply to this topic or send me a PM.

BR,
Paul

4

General Discussion / Re: Need help with config

« on: December 15, 2017, 11:54:32 pm »

PM sent 

5

General Discussion / Re: Multiple IPv4 subnets on one interface

« on: December 13, 2017, 11:00:36 am »

I will try to find out but I doubt they do. These switches were shipped to us by our customer so we're not in a position to swap anything unfortunately. I guess one of the switches is even unmanaged or has some kind of issue with remote access.

6

General Discussion / Re: Multiple IPv4 subnets on one interface

« on: December 13, 2017, 10:49:46 am »

Yes, we have hardware switches in both racks behind the OPNsense router.

Yes, we have a bridge set up. Does it mean we need to specify the subnets via virtual IP only on one interface which is a part of the bridge?

7

General Discussion / Multiple IPv4 subnets on one interface

« on: December 13, 2017, 10:02:14 am »

Hi,

I wonder if there's a way to hook up several IPv4 subnets to multiple interfaces simultaneously? Our topology is as follows: two incoming interfaces from our upstreams (dynamically routed via BGP) and two outgoing to two server racks. We tried virtual IPs but the GUI only allows us to add a single /24 subnet to each interface then it says "This IP address is being used by another interface or VIP". Any ideas on how this can be fixed?

8

General Discussion / Network config file location and multiple IP on one interface

« on: December 07, 2017, 01:31:19 pm »

Hi guys,

As far as I understand it's not possible to assign multiple IPs or subnets to a single interface via webgui?  I wonder if it's possible to do it directly via the config file? Where is the config file located?

Thanks in advance!

BR,
Paul

9

General Discussion / Re: Need help with config

« on: December 04, 2017, 08:29:16 am »

Hi again,

Just realized I probably had to post in General Discussion topic. Hey mods, could you please move this thread over there?

10

General Discussion / Re: Need help with config

« on: December 03, 2017, 09:09:33 am »

Thanks for your speedy response!

Depends on your upstream connection how you get those IPs.

We're receiving them from our upstreams, also as static subnets, they're PA aggregatable. Then we'll need to push them to our customer's AS on an OPNsense router. The customer will have 2 server racks with us, each port (interface) wired to a separate rack.     

arp -s host mac
should work

Just a suggestion: why not introducing a "Make Static" button next to the MAC/IP pair in ARP table? Mikrotik devices have a similar button and it's very convenient.

Thanks again!

11

General Discussion / Need help with config

« on: December 02, 2017, 11:26:40 pm »

Hi guys,

I'm new here, would like to say hi to the community/all OPNsense users!

We're considering OPNsense as a routing solution for one of our customers.  However there are some minor issues:

1. We're unable to find BGP IN/OUT filters. Perhaps they're called differently in FreeBSD world?
2.  We located the ARP table but there seems to be no option to set static ARP. Can it be done via the console perhaps?
3.  The customer is planning to use static IPs leased from us on his network what would be the correct way to forward these IPs from our network to their OPNsense router's interfaces?
4. What about IPv6? Anyone here running IPv6 on OPNsense? Any tips/hints or feedback?

Thanks in advance,
Paul