Messages

1

18.1 Legacy Series / Re: IGMPProxy1.3 is not starting

« on: January 15, 2019, 06:54:00 pm »

Hey,
I am now using the MR401 since 2 weeks.
Only firmware upgrades are not possible, since I am struggling with the tftp proxy.
Everything else has been working great.
No issues with watching TV.

Did you try it Frank?

Hi @gilddie, Hi to everyone,
I'm currently not able to get the MagentaTV IPTV working on my BNG based FTTH connection. I run my OPNSense directly connected to the FTTH Modem with an VLAN 7 Tagged Interface which is used by my PPPoE based WAN interface. I have tried several FW-Rulesets and also configured the IGMP-Proxy but the IPTV stream starts to stuck after round about 30 seconds streaming.

Could someone post his detailed FW-Rulesset and IGMP-Proxy settings that he/she used to get IPTV working on a Telekom based link using a OPNSense FW?

Thanks for any help in advance - I can post a more detailed config of my current setup if needed,

Cheers,

FillFeile

2

18.7 Legacy Series / Re: Firewall Log not working

« on: August 30, 2018, 05:25:56 pm »

@marjohn56 you made my day! Clearing /var/log an restarting the daemon did the trick.

syslogd is not eating up the RAM anymore and the firewall live logging works again.

Thank you some much! 

3

18.7 Legacy Series / Re: Firewall Log not working

« on: August 29, 2018, 06:19:02 pm »

Sadly I didn't find any message from my syslog deamon in my system.log. Here is the most current content and nothing was added after the daemon died again:

Code: [Select]

Sep 29 10:59:23 OPNsense configd.py: [32ea2b13-4821-48a8-9d0b-78a481c59ffa] request pfctl byte/packet counters
Sep 29 10:59:30 OPNsense configd.py: [d82f2168-41c7-4f26-b655-4543d180a8ef] request pfctl byte/packet counters
Sep 29 10:59:37 OPNsense configd.py: [7e116d12-1f8e-4377-9d59-a4ca92d14732] request pfctl byte/packet counters

I debugged a little more on my side and made an interesting discovery - after starting the syslog service via the web interface the syslogd process shows up in the process list. Observing the process list for a little while showed be this:

Code: [Select]

PID USERNAME  THR PRI NICE   SIZE    RES STATE   C   TIME    WCPU COMMAND
 3494 root             1  25    0  1051M   602M bo_wwa  3   0:12   8.49% syslogd
 3494 root             1  24    0  1051M   760M bo_wwa  3   0:15   9.63% syslogd
 3494 root             1  25    0  1051M   843M bo_wwa  3   0:17   9.78% syslogd
 3494 root             1  26    0  1051M   929M bo_wwa  0   0:20  11.04% syslogd
 3494 root             1  27    0  1051M  1029M bo_wwa  2   0:23   7.54% syslogd

The reserved (I think this is what RES stands for?) memory grows over time and the services dies after hitting the 1051M border.

Any ideas?

4

18.7 Legacy Series / Re: Firewall Log not working

« on: August 28, 2018, 05:08:28 pm »

Thanks for your fast answer Animosity022!

Actually there is on syslog file under /var/log...

Code: [Select]

root@OPNsense:/var/log # la
./                      flowd.log.000006        pf.today                suricata.log.2
../                     flowd.log.000007        pf.yesterday            suricata.log.3
bsdinstaller/           flowd.log.000008        portalauth.log          suricata.log.4
configd.log             flowd.log.000009        ppps.log                suricata.log.5
dhcpd.log               flowd.log.000010        relayd.log              suricata.log.6
dmesg.today             gateways.log            resolver.log            suricata.syslog.log
dmesg.yesterday         installer/              routing.log             system.log
dnsmasq.log             ipsec.log               setuid.today            userlog
filter.log              lastlog                 setuid.yesterday        utx.lastlogin
flowd.log               lighttpd/               squid/                  utx.log
flowd.log.000001        lighttpd.log            squid.syslog.log        vpn.log
flowd.log.000002        mount.today             suricata/               wireless.log
flowd.log.000003        ntp/                    suricata.log
flowd.log.000004        ntpd.log                suricata.log.0
flowd.log.000005        openvpn.log             suricata.log.1

Any ideas?

5

18.7 Legacy Series / [SOLVED] Firewall Log not working

« on: August 27, 2018, 05:48:31 pm »

Hi all,

System Info:  OPNsense 18.7.1_3-amd64 on AMD GX-412TC SOC

Currently I'm facing an strange issue with my OPNSense box. A while ago I noticed that my firewall logging is not updating anymore (and so do other logs like System->Log Files->General).

For example if I go to Firewall>Log Files>Live View the last entries there are from March this year - and no current log events are displayed. The firewall itself seems to work just fine by the way.

I also recognized that the syslog service on the dashboard is stopped - if I try to restart the service it runs for a couple of minutes and dies again afterwards. Could this be related?

Any suggests? Can I provide you with additional information?

Cheers,

FillFeile

6

General Discussion / Re: IDS and Proxy on PCEngines apu2 not working

« on: January 03, 2017, 04:45:10 pm »

Only for reference:

I just updated OPNsense to verison 16.7.12 and now the IDS & web proxy settings are not broken anymore.

So this issue is solved for me

7

General Discussion / [SOLVED] IDS and Proxy on PCEngines apu2 not working

« on: January 03, 2017, 01:51:11 pm »

Hello together,

I just installed OPNsense on my fresh arrived PCEngines apu2 with an 16GB SSD.

I used the following image to install: OPNsense-16.7-OpenSSL-serial-amd64.img

Everything seems to work fine, but if I try to setup either the proxy or the IDS feature OPNsense shows me only a broken settings page (see the picture in the attachments).

Does anyone know the reason for this? I read some posts in this forum where people used the IDS and proxy feature on my hardware...

I know that 16 GB of storage are not sufficient for operating both of the with many users, but I would like to give it a try..

Thanks for your help

FillFeile