Messages

1

Hardware and Performance / Re: Intel I217LM - 100baseTX <full-duplex>(not working at gigabit)

« on: May 03, 2022, 10:00:38 pm »

Just one additional troubleshooting thought would be to set the switch port to Gigabit rather than auto negotiate if that's possible.  Let us know if you find a solution.  I have a SFF PC with this card and I'd like to move my OPNsense install to it.

2

21.7 Legacy Series / Re: OPNSense, 21.7, GeoIP, MaxMind, IPv6 aliases error: "Invalid argument. [ALIAS]"

« on: August 02, 2021, 08:53:01 pm »

Do you happen to know what the default value for "Firewall Maximum Table Entries" is?

3

21.1 Legacy Series / Re: [SOLVED] Upgrade from clean install of OPNsense 21.1 to OPNsense 21.1.9 ?

« on: August 02, 2021, 06:06:33 pm »

Thanks Franco, you were right.  I was able to upgrade to 21.1.9 without ending up on 21.7 yet.  Thanks for the help.

4

21.1 Legacy Series / [SOLVED] Upgrade from clean install of OPNsense 21.1 to OPNsense 21.1.9 ?

« on: August 02, 2021, 03:19:36 am »

I've installed a fresh copy of OPNsense 21.1 and restored from backup config file.  I'd like to update to just OPNsense 21.1.9 and hold off on 21.7 for a bit and stay at 21.1.9 but when I check for updates it wants to install 21.7 and I just can't seem to find a config setting to stay on 21.1.x Marvelous Meerkat series.  Any assistance would be greatly appreciated.

5

21.1 Legacy Series / Many thanks and the traffic graphs are beautiful!

« on: March 15, 2021, 11:17:05 pm »

Just wanted to say thanks to franco and the entire team for all their hard work and efforts on the incredible project.

The traffic graphs really look amazing.

6

General Discussion / Re: How to enable log forwarding?

« on: December 20, 2020, 12:13:07 am »

Where is the "SEM Console Settings page" ?

7

General Discussion / Re: How to enable log forwarding?

« on: December 19, 2020, 08:29:50 pm »

Thanks.  I'm not sure how I managed to miss that      I'm guessing the "filter (filterlog)" would be the same stuff that's seen in the firewall live log view?

8

General Discussion / How to enable log forwarding?

« on: December 19, 2020, 04:31:42 am »

I'd like to forward logs to Alien Vault OSSIM but I can't seem to find the setting to do this anywhere in OPNsense.  Is this log forwarding possible?

9

General Discussion / Re: Do you use / does it makes sense? (SIEM)

« on: December 19, 2020, 04:04:47 am »

Any luck with this?  I'd like to configure OPNsense to use AlienVault OSSIM's SIEM as well.

10

19.7 Legacy Series / DHCPv4 Service - Removed domain field vaule, but it's not removed on clients

« on: December 17, 2019, 03:16:24 am »

Hi,

I'm wondering if this is expected behavior or perhaps a bug.  I want to remove the domain line listed in my DHCPv4 clients' /etc/resolv.conf and have no domain line listed.  They were getting this value from my OPNsense DHCPv4 server.

I cleared/deleted the value in the domain field on my OPNsense DHCPv4 server, but it was never removed from the clients.  I tried releasing/renewing at the clients and also waited a day.  I ended up replacing the blank field with something a different value and then that new value was sent to the clients.

Is it not possible to entirely remove the domain value from DHCPv4 clients' /etc/resolv.conf?

Thanks.

11

19.7 Legacy Series / Re: Firewall/Aliases -> Ports not working

« on: October 14, 2019, 02:55:00 am »

What's the number of that patch please?  Is there a page to see/watch for patches?

12

19.7 Legacy Series / Re: Entering alias is not working

« on: October 13, 2019, 11:02:58 pm »

I've tried patching using "opnsense-patch 7a5a271" as well as manually editing the opnsense.js file with the changes but I'm still having issues with aliases.  I don't see any content in them when I first try to edit them and then when I do see their contents (after a 2nd attempt at editing one), I can't add any new networks to the alias.

I've had to roll back to 19.7.4 to get things working again using "opnsense-revert -r 19.7.4 opnsense".

13

19.1 Legacy Series / Re: Aliasing completely broken for me recently

« on: April 16, 2019, 04:48:08 am »

I'm having similar issues with aliases with 19.1.6.  I've added a CIDR to an existing alias that only has about 28 other CIDRs to in order to block continuous SPAM from the new CIDR I'm adding and it as if I didn't even add it.  I keep getting SPAM from an address in the CIDR block that I added to the existing alias.  CIDR's added to the alias prior to the 19.1.6 upgrade are blocked as expected.

14

19.1 Legacy Series / Re: "Cannot allocate memory" error after applying alias edit

« on: March 24, 2019, 06:04:20 pm »

Thanks for the reply Ad.

I had that setting at 500000, but just now changed it to 1000000 and that seems to have resolved the issue.  I also noticed that after increasing it some of my other firewall rules, that I thought were working but really weren't, finally started working.

Many thanks for the assistance.

ObecalpEffect

15

19.1 Legacy Series / [RESOLVED] "Cannot allocate memory" error after applying alias edit

« on: March 23, 2019, 05:55:42 pm »

Hi,

I receive the popup error "Cannot allocate memory" after I hit apply in the Firewall/Aliases section.  I've discovered that I don't have to add/edit or change any of the aliases but if I even simply go to the Aliases section and hit "Apply" after making no changes, I still get the error.



I do have quite a few aliases that contain a large number of CIDRs but this error is something relatively new, maybe only started after that last two updates.

I'm using the current, up to date v19.1 production series:
OPNsense 19.1.4-amd64
FreeBSD 11.2-RELEASE-p9-HBSD
OpenSSL 1.0.2r 26 Feb 2019

Is there a tunable that I could adjust or should I start examining my large aliases perhaps?

Any assistance would be greatly appreciated.

Thanks,
ObecalpEffect.