Topics

Hi!

Is there a guide on doing this?  The documentation found in OPNsense works only to non-Wireguard Interfaces.  My Present set-up port forwards all DNS queries to my Adguard home and it work flawlessly however, it doesn't work for Wireguard interfaces, Internet traffic stops.

What would be a good practice running Torguard App on Client Side?  Most of the guides found here are about running wireguard inside OPNsense.

What Firewall Rules and NATs need to be set for seamless flow of traffic both getting out and coming in?

Hi!

I'm using this GPS:

BU-353N5 GPS Receiver

Are there any configuration that I could use to optimize it's performance?  Right now I'm just using "Generic".  I'm getting a lot of "False Ticker".  Dunno if it's configuration related

Mimugmail

New version v0.107.54 is available and it's not updating in OPNsense v2.7.8

Hi!

I have a spare static IP.  I am planning to use exclusively for a host in my Lan.net. What would be the best practice to do this?

So, far I'm thinking the ff:

1.  Create Virtual IP with the Spare Static IP
2.  Create a Rule in LAN for the host using the Virtual IP as GateWay

or

3.  Create a port forwarding Rule

4. Crete OutBount NAT Rule

For 3 & 4 not sure how to do this.

Any thoughts?

Hi!

Do you have any tips on dhcp options that I may try that will enhanced connectivity?  Trying to make some experiments that may help me with the following when my modem is in bridge-mode:

1.  Faster issuance of IP
2.  Limit lease renewal or Ip change.  ISP renews or change IP every 24 hours

ISP refuses to share any info on this

Thanks

I noticed some fields have this displayed instead of the value that was assigned to it:

"overall type: unknown_type html type: HTML_TYPE"

Upon chcking the config file the proper value is saved and present.

Is there any way to correct this?

Can someone help me interpret this error mesage:

Starting squid.
CPU Usage: 0.006 seconds = 0.006 user + 0.000 sys
Maximum Resident Size: 19200 KB
Page faults with physical i/o: 0
2024/02/27 10:56:56| Processing Configuration File: /usr/local/etc/squid/squid.conf (depth 0)
2024/02/27 10:56:56| WARNING: aclIpParseIpData: Netmask masks away part of the specified IP in '10.0.10.1/24'
2024/02/27 10:56:56| WARNING: aclIpParseIpData: Netmask masks away part of the specified IP in '10.0.30.1/24'
2024/02/27 10:56:56| WARNING: aclIpParseIpData: Netmask masks away part of the specified IP in '10.0.40.1/24'
2024/02/27 10:56:56| WARNING: aclIpParseIpData: Netmask masks away part of the specified IP in '10.0.50.1/24'
2024/02/27 10:56:56| WARNING: aclIpParseIpData: Netmask masks away part of the specified IP in '10.0.60.1/24'
2024/02/27 10:56:56| Processing Configuration File: /usr/local/etc/squid/pre-auth/40-snmp.conf (depth 1)
2024/02/27 10:56:56| Processing Configuration File: /usr/local/etc/squid/pre-auth/dummy.conf (depth 1)
2024/02/27 10:56:56| Processing Configuration File: /usr/local/etc/squid/pre-auth/parentproxy.conf (depth 1)
2024/02/27 10:56:56| ERROR: ACL not found: Safe_ports
2024/02/27 10:56:56| Not currently OK to rewrite swap log.
2024/02/27 10:56:56| storeDirWriteCleanLogs: Operation aborted.
2024/02/27 10:56:56| FATAL: Bungled /usr/local/etc/squid/squid.conf line 99: http_access deny !Safe_ports
2024/02/27 10:56:56| Squid Cache (Version 6.6): Terminated abnormally.
/usr/local/etc/rc.d/squid: WARNING: failed to start squid

Hi!

Im upgrading my NIC from I350 T4 - > Qnap I225-v 4 Ports.  What would by the best way to do this?

I'm considering MSS value 1448.  I just would like to confirm that I understood it right what is indicated on the "help".  It would deduct a value of 40 on the MSS field.  So, the value that I need to put on the field is MSS 1488.  Is that right?

Hi!

I'm new to opnsense.  I was making entries in the tunables section.  After reboot I noticed that the very same entries were also made in Loader.conf.  Isn't this redundant?  Can I  make the entries in Loader.Local.conf instead?