Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Topics - Onkel-tobi

#1
Hi all,

i am on 24.1.9_4-amd64 and I don't have any clue why traffic is still blocked 8seeattachment dropped_packages).
It's regarding my home automation network and I have a general RFC1918 rule that denies traffic within the vlan.
Now I am trying to connect from device 192.168.178.30 (random tcp port) to 192.168.178.88 on tcp port 8083.
As you can see in my screenshots this traffic is blocked with the RFC rule. But before I have a rule that should pass that traffic. (see rule1 and rule_details).
Do you have any hints for me?

Thanks,
Tobias
#2
Hi all,

unfortunately my wireguard site2site is not working after upgrade.
Wiregard for clients remains working.
I have the following setup:
Interface:

Tried with and without dynamic GW policy and with tunnel interface.
WG instance:

Tried without and with GW. Before update I didn't create a GW there.
Peer: didn't change anything
Gateway:


Any hint?
Thanks,
Tobias

Update: I have solved this by deleting all VPN related rules, restart and then manual configuration Gateway and rout and WG instance (disabling rules, setting GW).
#3
Hi,

i am just switching from IPSec to Wireguard for my S2S connection to my father.
Attached you can see the rough overview.

The link is shown as up and running but I can't access for example the Fritzbox on the other side.
connection shows:
peer: blubbblubb
  preshared key: (hidden)
  endpoint: [IPv6]:50040
  allowed ips: 192.168.200.0/24, 192.168.161.1/32
  transfer: 0 B received, 1.59 KiB sent
  persistent keepalive: every 25 seconds

Routing is done automatically, correct?
At least I have a route like 192.168.200.0/24 via wg2 (interface s2sPapa).
I can also see packages going out (see screenshot2).
What am I doing wrong?

Thanks for any hint,
Tobi
#4
General Discussion / accessing ipv6 IPs on WAN
February 11, 2024, 09:58:17 AM
Hi,

i am trying to establish a Wireguard site2site connection from an opnsense to a fritzbox.
Fritz!Box is only having IPv6 address now and I found out that I am not able to connect to ipv6 addresses.
My OPNSense is sitting behind a fritzbox with ipv4 address.
I have now enabled also ipv6 on WAN interface (DHCPv6) but it is not working.
Any hints?

Thanks,
Tobi
#5
Hi all,

i am just wondering why i have to create rules for the way back.
I have 6 ports (1 wan, 5 different ports with 8 vlans in all) configured.
For each vlan a single gateway is configured (is that really neede, as it seems to make no difference?).

Then i have created default block rules for incoming traffic.
Now i want access an http site from vlan a to b and created a rule for that.
But in the log i can now see that in this example traffic is going to vlan b but then the it is blocked on the interface b on going out.

I thought by default the way opnsense is doing it would be stateful, so if client from vlan a is initiating the traffic i don't need to create rules for the way back?

Does anyone have a hint on that?

Thanks,
Tobi
#6
Hi,

i have the following setup:
Fritzbox => opnsense
- I have forwarded port 51820 to the opnsense
- configured wireguard via https://docs.opnsense.org/manual/how-tos/wireguard-client.html (without any ipv6 setup)

My mobile phone is connecting but it shows its connected to ipv6 address and i can't find anything in the FW logs or even in the Wireguard handshake.

Any ideas?
Thanks,
Tobi
#7
Hi,

i am new here and am currently using an unifi security gateway and want to change the FW to an opnsense environment.
I am searching for a good but also cost optimized setup (< 500 € if the comprimisses are not to high).
Currently i have the following network devices:
- FW: USG
- AP: 3x UNifi U6 Pro
- Switches (all unifi):
1x 24 port switch
1x 8 port
3x 5 port
An Active Directoy running on synology nas and a pi hole + adguard running via Docker.
Homebridge also working as docker on synology.
- network/client devices: 60-80 (a lot of home automation devices)

my requirements are:
- WAN throughput: min. 500 mbit incl. IPS
- content finltering
- up to 10 remote dial in vpn user/divices
- up to 5 site to site vpns via wireguard or openvpn
- around 10 vlans
- possibility for WAN failover (via USB 4g/5g stick)
- no fans
- minimum of 4 gigabit lan ports (i expect i can use vlan tagging to summarize some vlans)

Does anyone has a proposal for such a hardware?

Thanks,
Tobi