Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Topics - agustinrojen

#1
Hey guys! Im planning to use Captive Portal for the use of.

Allowing only listed MAC addresses to obtain IP address, connect to the internet, and to give a specific bandwidth to the specific IP address.

But. I'm really stuck on where to start/begin? Please help me and give me some hints and suggestions. Thank you!
#2
Can you give.me advices or suggestions on what to do or what to use to limit bandwidth of a specific MAC address? Thank you!
#3
Can I have advice or suggestion to block adult sites on my LAN Opnsense?
#4
As seen in the image attached below. That will be my setup.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4: 192.168.1.1/24 (default. never changed after installation.
WAN(ue0) -> v4/DHCP4: 192.168.254.101/24

As you can see. Instead of using wireless driver NIC for my WAN. I used my first wired NIC as indicated below for my WAN interface, from Modem to OPNSense. That is why I got 192.168.254.101/24

So. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

and my question is..

How do I set up OPNSense to give clients IP address, Gateways, and DNS? for internet connection.
As indicated below. I will be using my second wired NIC from OPNsense to my Switch and my Switch to the Clients.

Can someone help me with my problem? Btw. I'm a newbie when it comes network security. So, it'll be much appreciated if you gentlemen/women could help me. Thank you! I'll be waiting for your thoughtful replies.  :)

From Philippines.
#5
As seen in the image attached below. That will be my setup.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4: 192.168.1.1/24 (default. never changed after installation.
WAN(ue0) -> v4/DHCP4: 192.168.254.101/24

As you can see. Instead of using wireless driver NIC for my WAN. I used my first wired NIC as indicated below for my WAN interface, from Modem to OPNSense. That is why I got 192.168.254.101/24

So. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

and my question is..

How do I set up OPNSense to give clients IP address, Gateways, and DNS? for internet connection.
As indicated below. I will be using my second wired NIC from OPNsense to my Switch and my Switch to the Clients.

Can someone help me with my problem? Btw. I'm a newbie when it comes network security. So, it'll be much appreciated if you gentlemen/women could help me. Thank you! I'll be waiting for your thoughtful replies.  :)

From Philippines.
#6
General Discussion / Connecting to WAN?
January 24, 2018, 12:14:06 PM
How do I connect my OPNSense box into a WiFi? To get a DHCP server IP from my modem? Please help.
#7
Here's the image. Do you idea on how i fix it? Thank you.
#8
Is the setup from pfsense the same with opnsense? Please help. I already have connection between modem and OPNsense. Now. From OPN sense to switch using the other LAN port. Therefore, I connected other PC devices into the switch as indicated in the atrachment picture. There is no internet access. So how do i setup my opnsense as a router? Am i gonna do bridging? Etc. Or what?

Thank you!
#9
General Discussion / There is no connection. [HELP]
January 23, 2018, 02:29:57 PM
 I used this setup for my firewall. I receive internet from my modem to my firewall. It is okay. But when i connect.my switch to the other lan port of my firewall and connect other pc. to switch. There is no connection. What do i need to do? Pls help. Please see attachment
#10
The right laptop has OPNsense. On left, it has windows. So these two units are connnected to Globe Home Broadband Modem (LAN)

Is possible to block websites? in windows unit using this setup and opnsense on right unit?

Pls helo. Newbie here. Thank you!
#11
I have an IP address on my OPNsense, 192.168.1.15 (LAN).

And another IP address for my other device 192.168.1.9 (LAN).

It seems that in my shell. I pinged my other device, 192.168.1.9 using my OPNSense. It goes through and it is pinging because my other device firewall was off.

and when I pinged my OPNSense, 192.168.1.15 using my other device. It just says request time out? I just wonder. How do I turn off my OPNSense firewall like windows firewall? Thank youuu.

newwbiee here.
#12
Does OPNSense have the following features?  ??? ???

• Bandwidth Limiter (e.g. Bandwidth is 10 Mbps.)
Computer 1 = 2 Mbps
Computer 2 = 2 Mbps
Computer 3 = 2 Mbps
Computer 4 = 2 Mbps
Computer 5 = 2 Mbps
• Block/Restrict unwanted websites
• Captive Portal (for MAC Address Filtering)
That only allows registered MAC addresses to connect to the internet.

Thank you!  :)
#13
Does OPNSense have the following features?  ??? ???

• Bandwidth Limiter (e.g. Bandwidth is 10 Mbps.)
Computer 1 = 2 Mbps
Computer 2 = 2 Mbps
Computer 3 = 2 Mbps
Computer 4 = 2 Mbps
Computer 5 = 2 Mbps
• Block/Restrict unwanted websites
• Captive Portal (for MAC Address Filtering)
That only allows registered MAC addresses to connect to the internet.

Thank you!  :)