Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - agustinrojen

Pages: [1] 2

General Discussion / Captive portal: Allow only listed MAC Address.

« on: January 27, 2018, 07:13:30 pm »

Hey guys! Im planning to use Captive Portal for the use of.

Allowing only listed MAC addresses to obtain IP address, connect to the internet, and to give a specific bandwidth to the specific IP address.

But. I'm really stuck on where to start/begin? Please help me and give me some hints and suggestions. Thank you!

17.1 Legacy Series / Limit bandwidth use of a specific MAC address?

« on: January 27, 2018, 05:48:52 pm »

Can you give.me advices or suggestions on what to do or what to use to limit bandwidth of a specific MAC address? Thank you!

17.1 Legacy Series / Re: Method to block adult sites? Thank you

« on: January 27, 2018, 05:47:09 pm »

Problem solved with Family Protection ADGuard! Thank you.

17.1 Legacy Series / Re: Method to block adult sites? Thank you

« on: January 27, 2018, 05:27:21 pm »

Sir fabian. I followed the webproxyfilter. Nothing changes. I can still open adult sites

17.1 Legacy Series / Method to block adult sites? Thank you

« on: January 27, 2018, 03:49:05 pm »

Can I have advice or suggestion to block adult sites on my LAN Opnsense?

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 27, 2018, 12:44:14 pm »

Uhm mr. Hutiucip. I followed all ur instructions. and i succesfully entered my opnsense web GUI using the lan default 192.168.1.1 using my switch and client unit even though my WAN is 192.168.254.100 via dhcp.

But the problem now is. I can access.my opnsense web gui using my.clients. but my clients doesnt have internet.connection. what does that mean? Am i going to.configure something on opnsense. To have internrt connectoon in my clients?

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 27, 2018, 12:06:36 pm »

Excuse me. The internet and Modem in my situation is one.

Its a LTE modem that has a wifi and lan built to it and supplied internet by sim card. Default gateway is 192.168.254.254

It has 4 ports LAN ports.

LAN1 -- LAN2 -- LAN3 --LAN/WAN

Where should I connect it? From modem to opnsense.

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 27, 2018, 10:56:19 am »

up.

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 27, 2018, 08:40:02 am »

I got it from. MODEM(Internet) to OPNSense(WAN DHCP)
It is WAN 192.168.254.102 via DHCP and I got replies from websites when i pinged them.

But. I really dont have idea on what you said. OPNSense(LAN Static) to switch. What IP do i need to put on my static LAN? Gateway and DNS'S?

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 27, 2018, 05:00:48 am »

Because I wil be using a wired NIC for my WAN. How can i access web GUI then?

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 27, 2018, 04:34:03 am »

But. How can i access my Web GUI if.my.first wired nic will be WAN?

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 26, 2018, 09:14:01 pm »

What do I need to do sir? I cant understand it

Heres my diagram to follow.

17.1 Legacy Series / Re: How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 26, 2018, 08:06:48 pm »

Im sorry sir. I think I've explained my setup wrong and in the other way. Please read this again. It's just a vice versa.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4:/DHCP4: 192.168.254.101/24
WAN(ue0) -> v4/DHCP4:

As you can see. Instead of using wireless driver NIC for my WAN. I used my second wired NIC as indicated below for my WAN interface.

I got 192.168.254.101/24 on my LAN interface because it was set into DHCP.

I just recently configured my DHCP server for LAN interface. But before I can configure dhcp server. I must make my LAN interface into a static form right?

So I change my LAN interface into static.

LAN (re0) -> v4:: 192.168.254.1/24
WAN(ue0) -> v4/DHCP4:

Then. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

Then. I've already change my LAN IP into static. I just finished configuring my DHCP server for my LAN interface. But. How can I give my WAN an IP address(internet connection from my DHCP server). How can I give IP address or internet connection to my clients if my WAN interface doesn't have one. My WAN interface is set to DHCP4. I thought it will have an IP coming from my LAN DHCP. Am I wrong? Please help me.

So it'll be. MODEM -> OPNSense (LAN Static) DHCP Server -> OPNSense(WAN DHCP4) -> SWITCH -> CLIENTS

Thank you again!

From Philippines.

17.1 Legacy Series / How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 26, 2018, 06:07:15 pm »

As seen in the image attached below. That will be my setup.

Default Internet IP Gateway: 192.168.254.254

My OPN Interfaces.

LAN (re0) -> v4: 192.168.1.1/24 (default. never changed after installation.
WAN(ue0) -> v4/DHCP4: 192.168.254.101/24

As you can see. Instead of using wireless driver NIC for my WAN. I used my first wired NIC as indicated below for my WAN interface, from Modem to OPNSense. That is why I got 192.168.254.101/24

So. I opened shell in my OPNsense and ping websites(google, facebook, etc.) to test my connection. Hopefully, I got a reply and it can ping those websites.

and my question is..

How do I set up OPNSense to give clients IP address, Gateways, and DNS? for internet connection.
As indicated below. I will be using my second wired NIC from OPNsense to my Switch and my Switch to the Clients.

Can someone help me with my problem? Btw. I'm a newbie when it comes network security. So, it'll be much appreciated if you gentlemen/women could help me. Thank you! I'll be waiting for your thoughtful replies.

From Philippines.

General Discussion / How to give clients IP Address, Gateways and DNS using OPNSense?

« on: January 26, 2018, 04:10:39 pm »

From Philippines.

Pages: [1] 2