Messages

hello, my internet speed was only used to 80-90% and that is probably due to the VLAN Interface Errors!
same error as here?! : https://github.com/opnsense/src/issues/74

this is a fresh installation! I didn't have an older version in operation before, so I can't say whether the error only appeared with the current version

my setup:
Proxmox VM
OPNsense OPNsense 22.1.1_1-amd64
WAN interface PCI passthrough (Realtek)
LAN VirtIO
3 VLANs

Code Select Expand


Name    Mtu Network       Address              Ipkts Ierrs Idrop    Opkts Oerrs  Coll
re0    1500 <Link#1>      00:01:2e:92:11:98   583847     0     0   201661     0     0
re0       - fe80::%re0/64 fe80::201:2eff:fe       20     -     -       28     -     -
re0       - 192.168.xxx.0 192.168.xxx.254        174     -     -      174     -     -
re0       - 2001:xxx:13c3 2001:xxx:13c3:a80        1     -     -       13     -     -
re0       - fdc8:de98:944 fdc8:de98:944d:17        0     -     -        0     -     -
vtnet  1500 <Link#2>      c2:ca:30:d5:16:84      528     0     0      309     0     0
vtnet     - 172.16.1.0/24 fw                    3119     -     -     6886     -     -
vtnet     - 2001:xxx:13c3 2001:xxx:13c3:a8f       27     -     -       30     -     -
vtnet     - fe80::%vtnet0 fe80::c0ca:30ff:f       60     -     -       81     -     -
lo0   16384 <Link#3>      lo0                  11699     0     0    11699     0     0
lo0       - ip6-localhost ip6-localhost            8     -     -        8     -     -
lo0       - fe80::%lo0/64 fe80::1%lo0              0     -     -        0     -     -
lo0       - your-net      localhost            11691     -     -    11691     -     -
enc0*  1536 <Link#4>      enc0                     0     0     0        0     0     0
pflog 33160 <Link#5>      pflog0                   0     0     0    10356     0     0
pfsyn  1500 <Link#6>      pfsync0                  0     0     0        0     0     0
vtnet  1500 <Link#7>      c2:ca:30:d5:16:84   186439     0     0   579363  2046     0
vtnet     - 172.16.2.0/24 172.16.2.1              92     -     -      421     -     -
vtnet     - 2001:xxx:13c3 2001:xxx:13c3:a8f       11     -     -       14     -     -
vtnet     - fe80::%vtnet0 fe80::c0ca:30ff:f       21     -     -       40     -     -
vtnet  1500 <Link#8>      c2:ca:30:d5:16:84     9311     0     0    10404     9     0
vtnet     - 172.16.3.0/24 172.16.3.1               1     -     -      882     -     -
vtnet     - 2001:xxx:13c3 2001:xxx:13c3:a8f        0     -     -        4     -     -
vtnet     - fe80::%vtnet0 fe80::c0ca:30ff:f        2     -     -        8     -     -
vtnet  1500 <Link#9>      c2:ca:30:d5:16:84       10     0     0       25     0     0
vtnet     - 172.16.4.0/24 172.16.4.1               0     -     -        0     -     -
vtnet     - fe80::%vtnet0 fe80::c0ca:30ff:f        0     -     -       21     -     -
vtnet     - 2001:xxx:13c3 2001:xxx:13c3:a8f        5     -     -        0     -     -



cheers
velvet

the problem is after the update to 20.1.1. and the final reboot occurred again

UPDATE: if I reactivate v6 after the reboot, v4 and v6 work again!

UPDATE II: I have now installed the Realtek driver - now the problem seems to be fixed! :)


velvet

Hi,

I have problems with IPv6. after a reboot I sometimes have no network - neither with v6 nor with v4. I don't get a v6 prefix and the dhcpv6 daemon process is stopped! a restart does not work - crashes again and again. only deactivating IPv6 on the WAN interface and a restart helps to get v4 going! a reboot of the fritzbox and OPNsense brings v6 and v4 to run again!

SETUP:
--------

WAN -> DS-Lite
   |
Fritzbox - 192.168.178.1/24
   |
OPNsense - 192.168.178.254/24 IPv6 PD /60 at WAN Interface
  |
LAN - 172.16.16.0/24


---
2022-02-16T13:19:43   Error   opnsense   /usr/local/etc/rc.routing_configure: The WAN_GW monitor address is empty, skipping.   
2022-02-16T13:19:43   Error   opnsense   /usr/local/etc/rc.routing_configure: ROUTING: keeping current default gateway '192.168.178.1'   
2022-02-16T13:19:43   Error   opnsense   /usr/local/etc/rc.routing_configure: ROUTING: setting IPv4 default route to 192.168.178.1   
2022-02-16T13:19:43   Error   opnsense   /usr/local/etc/rc.routing_configure: ROUTING: IPv4 default gateway set to wan   
2022-02-16T13:19:43   Error   opnsense   /usr/local/etc/rc.routing_configure: ROUTING: entering configure using defaults   
2022-02-16T13:19:42   Error   opnsense   /usr/local/etc/rc.bootup: Resyncing OpenVPN instances.   
2022-02-16T13:19:40   Error   opnsense   /usr/local/etc/rc.bootup: The WAN_GW monitor address is empty, skipping.   
2022-02-16T13:19:40   Error   opnsense   /usr/local/etc/rc.bootup: ROUTING: creating /tmp/re0_defaultgw using '192.168.178.1'   
2022-02-16T13:19:40   Error   opnsense   /usr/local/etc/rc.bootup: ROUTING: setting IPv4 default route to 192.168.178.1   
2022-02-16T13:19:40   Error   opnsense   /usr/local/etc/rc.bootup: ROUTING: IPv4 default gateway set to wan   
2022-02-16T13:19:40   Error   opnsense   /usr/local/etc/rc.bootup: ROUTING: entering configure using defaults   
2022-02-16T13:18:29   Error   opnsense   /interfaces.php: The command '/bin/pkill -'TERM' -F '/var/run/updaterrd.sh.pid'' returned exit code '3', the output was 'pkill: Cannot get process list (kvm_getprocs: No such process)'   
2022-02-16T13:18:29   Error   opnsense   /interfaces.php: The command '/usr/local/sbin/ntpd -g -c '/var/etc/ntpd.conf'' returned exit code '1', the output was ''   
2022-02-16T13:17:56   Error   opnsense   /interfaces.php: The WAN_GW monitor address is empty, skipping.   
2022-02-16T13:17:56   Error   opnsense   /interfaces.php: ROUTING: keeping current default gateway '192.168.178.1'   
2022-02-16T13:17:56   Error   opnsense   /interfaces.php: ROUTING: setting IPv4 default route to 192.168.178.1   
2022-02-16T13:17:56   Error   opnsense   /interfaces.php: ROUTING: IPv4 default gateway set to wan   
2022-02-16T13:17:56   Error   opnsense   /interfaces.php: ROUTING: entering configure using defaults   
2022-02-16T13:17:55   Error   opnsense   /interfaces.php: ROUTING: creating /tmp/re0_defaultgw using '192.168.178.1'   
2022-02-16T13:17:55   Error   opnsense   /interfaces.php: ROUTING: removing /tmp/re0_defaultgw
2022-02-16T13:17:55   Error   opnsense   /interfaces.php: ROUTING: removing /tmp/re0_defaultgw   
2022-02-16T13:17:55   Error   opnsense   /interfaces.php: ROUTING: setting IPv4 default route to 192.168.178.1   
2022-02-16T13:17:55   Error   opnsense   /interfaces.php: ROUTING: IPv4 default gateway set to wan   
2022-02-16T13:17:55   Error   opnsense   /interfaces.php: ROUTING: entering configure using 'wan'   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: The WAN_DHCP6 monitor address is empty, skipping.   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: The WAN_GW monitor address is empty, skipping.   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: skipping IPv6 default route   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: IPv6 default gateway set to wan   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: keeping current default gateway '192.168.178.1'   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: setting IPv4 default route to 192.168.178.1   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: IPv4 default gateway set to wan   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: entering configure using defaults   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: skipping IPv6 default route   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: IPv6 default gateway set to wan   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: creating /tmp/re0_defaultgw using '192.168.178.1'   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: removing /tmp/re0_defaultgw   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: setting IPv4 default route to 192.168.178.1   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: IPv4 default gateway set to wan   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: ROUTING: entering configure using 'wan'   
2022-02-16T13:17:28   Error   opnsense   /interfaces.php: Accept router advertisements on interface re0

does anyone have the same problem or a tip?

cheers,
velvet

I'm running this on my Dell Poweredge R210.  Have you all made sure that your Bios and firmware are up to date?  I made sure mine where all up to date before I built the box, as I just put this together last week and seems to be running well.

bios is up2date!
it's frustrating! I'm not the only one with the kernel panic!
even under vmware there are these problems! that's a joke!

I wanted to start a fresh installation - kernel panic!
on Dell PowerEdge R340!
No workaround helps! does anyone have a tip or any other help?