OPNsense Forum
English Forums => Hardware and Performance => Topic started by: Wyrm on January 17, 2020, 09:27:09 pm
-
I have this for use as opnsense firewall:
Barebone XtendLan EBF-224-V1605B
Barebone, Ryzen V1605B 4x 2,0GHz, 2x SO-DIMM, HDMI+DP, 2x LAN, 7x USB 2.0/ 3.0/ typ C, 1x COM, TDP 15W, fanless
There is installed 16GB RAM and M.2 64 GB SSD
I tried to install normal DVD image with latest opnsense and it stops with "power button".
I have 19.1. serial, so I tried it and there is copy of terminal text in attachements
When I boot FreeBSD 12 latest it goes well to run and it is possible to install FreeBSD 12 on it.
Is there some possibility to solve "power button" to finish the setup ?
Thanks for reply
-
Two questions:
Have you tried 19.7 ? The results could be helpful if still unsuccessful.
Also, assuming you have the latest BIOS, did you check if the boot process finishes and you get a DHCP IP on one of the NICs ? I'm wondering if the console may be freezing here since the end of the output is a bit unusual.
-
AMD Ryzen Embedded... nice i am curious. This will be a wonderful year :)
cheers
till
-
I have tried 19.7 and it was same, but i did not have serial version to copy content.
So for this reason I tried 19.1. which I have in serial usb install.
HW is just new and it certainly has actual bios. In bios there are lots of options, but in ACPI section is only possible to disable or enable ACPI or suspend.
HW has power on button but it is not something unusual.
It did not get to state to have IP address. If you check my attachments from last post there is no start of opnsense.
I will try to run all in VMWARE, but I would like to prefer to have this box only for opnsense...
So I will try 19.7. and we will see.
I could also try to boot vmware esxi to see if it will work.
-
Try booting 19.7 and do the following after a couple minutes from a directly connected machine. Set up your IP manually to be on the safe side.
ssh installer@192.168.1.1
-
Hi,
thank you. I wil try this...
Should I use serial or dvd version ?
-
Try booting 19.7 and do the following after a couple minutes from a directly connected machine. Set up your IP manually to be on the safe side.ssh installer@192.168.1.1
Hi,
I have tried it and nothing happened. I am trying it from Windows machine. I see in network adapter only 10Mbit speed, so the box is not running in right drivers. It has realtek net adapters.
I tried to install vmware and it worked nice - i will try to install opnsense in vmware and let you know...
-
AMD Ryzen Embedded... nice i am curious. This will be a wonderful year :)
cheers
till
Amen, @tillsense! I just bought the little brother to this guy and will get my hands on it Friday to try this out, too. Hope it'll detect the dual realtek just fine :)
-
AMD Ryzen Embedded... nice i am curious. This will be a wonderful year :)
cheers
till
Amen, @tillsense! I just bought the little brother to this guy and will get my hands on it Friday to try this out, too. Hope it'll detect the dual realtek just fine :)
Where did you buy it? I am looking to go in this direction.
-
I have a similar board the iBase IB918F-1505G and the same problem.
tested a few different systems:
- freeBSD 11.2 => freeze on acpi0: Power Button (fixed)
- freeBSD 11.3 => freeze on acpi0: Power Button (fixed)
- freeBSD 12.1 => Boots OK
- pfsense 2.4.4 => freeze on acpi0: Power Button (fixed)
- pfsense 2.4.5 => Boots OK
- OPNsense 20.1 => freeze on acpi0: Power Button (fixed)
- OPNsense 20.7.b => Boots OK
I did a little bit of digging and it seems like the problem is described in FreeBSD Bug 231760.
I have no idea if this is save to run or what the implications are but i got OPNsense 20.1 to boot by setting hw.pci.mcfg=0 in loader prompt.
-
Hi all,
I am writing here after quite long time.
My customer was running his box on vmware + opnsense.
When version 20.7 was released I tried to use it without VMWARE and it worked.
So then it worked several months to end of 2020.
All updates worked fine.
But there is new problem with version 21.1 which is current and it stops on this:
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xffffffff82967e10
vpanic() at vpanic+0x1a2/frame 0xffffffff82967e60
panic() at panic+0x43/frame 0xffffffff82967ec0
trap_fatal() at trap_fatal+0x39c/frame 0xffffffff82967f20
trap_pfault() at trap_pfault+0x49/frame 0xffffffff82967f80
trap() at trap+0x29f/frame 0xffffffff82968090
calltrap() at calltrap+0x8/frame 0xffffffff82968090
--- trap 0xc, rip = 0xffffffff812ac01b, rsp = 0xffffffff82968160, rbp = 0xffffffff829681b0 ---
xgbe_phy_reset() at xgbe_phy_reset+0x1b/frame 0xffffffff829681b0
xgbe_phy_reset() at xgbe_phy_reset+0x10/frame 0xffffffff829681d0
axgbe_if_attach_post() at axgbe_if_attach_post+0x324/frame 0xffffffff82968210
iflib_device_register() at iflib_device_register+0xfd4/frame 0xffffffff829685a0
iflib_device_attach() at iflib_device_attach+0xb7/frame 0xffffffff829685d0
device_attach() at device_attach+0x3e1/frame 0xffffffff82968620
bus_generic_attach() at bus_generic_attach+0x5c/frame 0xffffffff82968650
pci_attach() at pci_attach+0xd5/frame 0xffffffff82968690
device_attach() at device_attach+0x3e1/frame 0xffffffff829686e0
bus_generic_attach() at bus_generic_attach+0x5c/frame 0xffffffff82968710
acpi_pcib_pci_attach() at acpi_pcib_pci_attach+0xa1/frame 0xffffffff82968750
device_attach() at device_attach+0x3e1/frame 0xffffffff829687a0
bus_generic_attach() at bus_generic_attach+0x5c/frame 0xffffffff829687d0
pci_attach() at pci_attach+0xd5/frame 0xffffffff82968810
device_attach() at device_attach+0x3e1/frame 0xffffffff82968860
bus_generic_attach() at bus_generic_attach+0x5c/frame 0xffffffff82968890
acpi_pcib_acpi_attach() at acpi_pcib_acpi_attach+0x440/frame 0xffffffff82968900
device_attach() at device_attach+0x3e1/frame 0xffffffff82968950
bus_generic_attach() at bus_generic_attach+0x5c/frame 0xffffffff82968980
acpi_attach() at acpi_attach+0xd81/frame 0xffffffff82968a10
device_attach() at device_attach+0x3e1/frame 0xffffffff82968a60
bus_generic_attach() at bus_generic_attach+0x5c/frame 0xffffffff82968a90
device_attach() at device_attach+0x3e1/frame 0xffffffff82968ae0
bus_generic_new_pass() at bus_generic_new_pass+0x118/frame 0xffffffff82968b10
root_bus_configure() at root_bus_configure+0x77/frame 0xffffffff82968b40
configure() at configure+0x9/frame 0xffffffff82968b50
mi_startup() at mi_startup+0x118/frame 0xffffffff82968b70
btext() at btext+0x2c
KDB: enter: panic
[ thread pid 0 tid 100000 ]
Stopped at kdb_enter+0x3b: movq $0,kdb_why
db>
Is there somebody who could look at this and help with details?
Thanks.
-
Actually box is working again on opnsense but version 20.7 with latest updates.
After several boots of 21.1. i left it with 20.7.
So I will have to wait with some hope that newer version will work with this box.
If is there somebody who could help with some advice I would appreciate it ;)
-
AMD Ryzen Embedded... nice i am curious. This will be a wonderful year :)
cheers
till
Amen, @tillsense! I just bought the little brother to this guy and will get my hands on it Friday to try this out, too. Hope it'll detect the dual realtek just fine :)
Where did you buy it? I am looking to go in this direction.
I got mine from Newegg under AMD Ryzen VBOX 1000 or something.
-
Actually box is working again on opnsense but version 20.7 with latest updates.
After several boots of 21.1. i left it with 20.7.
So I will have to wait with some hope that newer version will work with this box.
If is there somebody who could help with some advice I would appreciate it ;)
Sorry, I only tried it with 20.7. Got it to work fine, didn't try newer.
I actually installed Hyper-V on the machine and put OpnSense in a VM on it with 3 cores. It is working fantastic.