OPNsense Forum
Archive => 19.7 Legacy Series => Topic started by: ktk on December 02, 2019, 07:53:49 pm
-
I have a super weird behavior with my PcEngines APU & LTE based ppp WAN connection (Sierra Wireless MC7430 Qualcomm Snapdragon X7 LTE-A):
I get the connection to work just fine, sets up fast after a reboot and I get a IPv4 address (no v6 and v4 is private IP). I can resolve names & do tcp/udp just fine.
When I do speedtest, download is fine, not as fast as my Wifi router but ok. When I do upload, the connection is slow and drops to zero very fast. After that my link is in nirvana mode for a while, still shown as ppp0 interface but can't do anything anymore. While monitoring the network I figured it happens after around 2.5MB outgoing traffic in general.
In ppps.log I see this the moment the link stalls: https://pastebin.com/tA6kystN
system.log:
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: IP renewal is starting on 'ppp0'
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: On (IP address: 10.131.180.114) (interface: WAN[wan]) (real interface: ppp0).
Dec 3 01:28:12 bidul opnsense: plugins_configure hosts ()
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: ROUTING: entering configure using 'wan'
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: ROUTING: IPv4 default gateway set to wan
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: ROUTING: setting IPv4 default route to 10.64.64.0
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: ROUTING: keeping current default gateway '10.64.64.0'
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: ROUTING: IPv6 default gateway set to wan
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: ROUTING: skipping IPv6 default route
Dec 3 01:28:12 bidul opnsense: plugins_configure monitor ()
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: The WAN_DHCP6 monitor address is empty, skipping.
Dec 3 01:28:12 bidul opnsense: /usr/local/etc/rc.newwanip: The WAN_PPP monitor address is empty, skipping.
The link seems to come back after a while but I can very easily trigger it again. I am quite convinced that it's related to how much traffic I *upload*, not to what I download. After around 2MB of outgoing traffic it goes down again, quickly tested it by scp-ing a file to a server.
When I have large downloads it happens at one point as well but I'm quite sure that's when I hit the ~2MB on ACKs or alike.
The interesting thing is that there seems to be something related to ICMP as well. Sometimes I can ping hosts in the Internet, sometimes not. But even if I can after a fresh reboot (and it's not always like this for whatever reason) I definitely won't be able to ping anything *after* the link went down the first time. I see outgoing echo requests on the ppp interface but never an answer.
I'm a bit lost here, this hardware used to work fine before. I recently started from scratch as it was not used for about a year and the only difference IMO is that I'm on a more recent opnsense release. I think the last one was not hardenedBSD yet, could that be a reason? If so, do we still have images I can get pre-hardened so I could test?
FWIW I've also updated the firmware on my LTE card, it was almost 3 years old. But same behavior with the latest release. LTE Signal is in general very good, MIMO antenna attached to it. All values are in Good or Excellent range (tx & rx).
-
Update: Tested the same setup on pfSense as well, same behavior. I start to suspect this is the u3g driver acting up.
-
Hi,
some LTE providers just block ICMP traffic and they put you in a private network so they can have more custommers connected with one public IP. This is called Carrier-grade NAT (CGN).
I suggest to disable Gateway Monitoring on the gateway menu, so your gateway wont be set as down after some failed PINGs.
-
Thanks for the tip, however this seems disabled by default on PPP according to what I see in System->Gateways.
However, I see this in mpd_wan.conf:
set link keep-alive 10 60
This seems related to the
LCP: no reply to 1 echo request
messages I see in the log before the link goes down. Setting this to 0 should disable the check according to the mpd docs.
However, I can't seem to override this as the file gets recreated on every restart.
kill HUP does not help either, mpd seems to get killed that way, not re-configured.
Anyone has an idea how I can override that for testing? can't find it in the UI so I guess this is hard coded.
-
Latest update: It is stable for 2 days no and I do not see the LCP errors anymore. Also upload speed is much better.
Strange thing is that I did not change anything IMO, maybe provider glitch.