I upgraded from V23 to V25
Tried to save a snapshot and was told I need ZSF
I am trying to do a serial console install of 25 but it keeps hanging ... see below
What must I do to resolve this. Thanks
I have a VP2420 -
VP2420 - 4x 2.5G Port Intel ® Celeron J6412 ×Vault:VP2420 - Core × 1
Memory:Crucial DDR4-3200 SO-DIMM Memory Module - 8GB × 1
Storage (m.2 SATA SSD):1TB Protectli M.2 SSD × 1
Operating System (Pre-installed m.2):
OPNsense 23.1 "Quintessential Quail" × 1 .. I upgraded to latest 25
BIOS:
coreboot (Open Source) BIOS × 1
The following is my boot log
/---------------------------------\
| Please select boot device: |
|---------------------------------|
| Protectli 1TB M.2 |
| Network Boot and Utilities |
| UEFI Shell |
| Setup |
|> USB Disk 2.0 |
|---------------------------------|
| ^ and v to move selection |
| ENTER to select boot device |
| ESC to exit |
\---------------------------------/
Consoles: EFI console
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/amd64 EFI loader, Revision 3.0
Command line arguments: loader.efi
Image base: 0x751b5000
EFI version: 2.70
EFI Firmware: EDK II (rev 1.00)
Console: efi (0x20000000)
Load Path: \EFI\BOOT\BOOTX64.EFI
Load Device: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x8,0x0)/HD(1,GPT,66BD4755-DD55-1
1EF-8F63-000C2995994A,0x22,0x10418)
BootCurrent: 0005
BootOrder: 0004 0002 0003 0000 0001 0005
BootInfo Path: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x8,0x0)
Ignoring Boot0005: Only one DP found
Trying ESP: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x8,0x0)/HD(1,GPT,66BD4755-DD55-11EF-
8F63-000C2995994A,0x22,0x10418)
Setting currdev to disk0p1:
Trying: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x8,0x0)/HD(2,GPT,66BD475D-DD55-11EF-8F63
-000C2995994A,0x1043A,0x7A)
Setting currdev to disk0p2:
Trying: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x8,0x0)/HD(3,GPT,66BD475F-DD55-11EF-8F63
-000C2995994A,0x104B4,0x400)
Setting currdev to disk0p3:
Trying: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x8,0x0)/HD(4,GPT,66BD4760-DD55-11EF-8F63
-000C2995994A,0x108B4,0x4E3600)
Setting currdev to disk0p4:
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
-
/
-
______ _____ _____
/ __ |/ ___ |/ __ |
| | | | |__/ | | | |___ ___ _ __ ___ ___
| | | | ___/| | | / __|/ _ \ '_ \/ __|/ _ \
| |__| | | | | | \__ \ __/ | | \__ \ __/
|_____/|_| |_| /__|___/\___|_| |_|___/\___|
+-----------------------------------------+ @@@@@@@@@@@@@@@@@@@@@@@@@@@@
| | @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
| 1. Boot Multi user [Enter] | @@@@@ @@@@@
| 2. Boot Single user | @@@@@ @@@@@
| 3. Escape to loader prompt | @@@@@@@@@@@ @@@@@@@@@@@
| 4. Reboot | \\\\\ /////
| 5. Cons: Dual (Serial primary) | )))))))))))) (((((((((((
| | ///// \\\\\
| Options: | @@@@@@@@@@@ @@@@@@@@@@@
| 6. Kernel: default/kernel (1 of 1) | @@@@@ @@@@@
| 7. Boot Options | @@@@@ @@@@@
| | @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
| | @@@@@@@@@@@@@@@@@@@@@@@@@@@@
+-----------------------------------------+
Autoboot in 0 seconds. [Space] to pause 25.1 ``Ultimate Unicorn'' \
Loading kernel...
/boot/kernel/kernel text=0x181ce8 text=0xe0fd78 text=0x45e00c data=0x180+0xe80 data=0x196780+0x469880 0x8+0x1a1c90+0x8+0x1c6c3f/
Loading configured modules...
/boot/kernel/pf.ko size 0x8e3d8 at 0x2169000
/boot/entropy size=0x1000
/boot/kernel/if_gre.ko size 0xaa30 at 0x21f9000
/boot/kernel/if_bridge.ko size 0xea58 at 0x2204000
loading required module 'bridgestp'
/boot/kernel/bridgestp.ko size 0x8930 at 0x2213000
/boot/kernel/carp.ko size 0xfba8 at 0x221c000
/boot/kernel/pflog.ko size 0x3c10 at 0x222c000
/boot/kernel/pfsync.ko size 0x11a18 at 0x2230000
/boot/kernel/if_lagg.ko size 0x165f0 at 0x2242000
loading required module 'if_infiniband'
/boot/kernel/if_infiniband.ko size 0x3540 at 0x2259000
/boot/kernel/if_enc.ko size 0x4be0 at 0x225d000
can't find '/etc/hostid'
staging 0x6bc00000 (not copying) tramp 0x7531a000 PT4 0x75311000
Start @ 0xffffffff80382000 ...
Timeout initializing vt_vga
KDB: debugger backends: ddb
KDB: current backend: ddb
---<<BOOT>>---
Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.2-RELEASE stable/25.1-n269614-36155813721 SMP amd64
FreeBSD clang version 18.1.6 (https://github.com/llvm/llvm-project.git llvmorg-18.1.6-0-g1118c2e05e67)
VT(vga): resolution 640x480
CPU: Intel(R) Celeron(R) J6412 @ 2.00GHz (1996.80-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x90661 Family=0x6 Model=0x96 Stepping=1
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x101<LAHF,Prefetch>
Structured Extended Features=0x2394a2c3<FSGSBASE,TSCADJ,FDPEXC,SMEP,ERMS,NFPUSG,PQE,RDSEED,SMAP,CLFLUSHOPT,CLWB,PROCTRACE,SHA>
Structured Extended Features2=0x18400124<UMIP,WAITPKG,GFNI,RDPID,MOVDIRI,MOVDIR64B>
Structured Extended Features3=0xfc000400<MD_CLEAR,IBPB,STIBP,L1DFL,ARCH_CAP,CORE_CAP,SSBD>
XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
IA32_ARCH_CAPS=0x20c6b<RDCL_NO,IBRS_ALL,SKIP_L1DFL_VME,MDS_NO>
VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8115159040 (7739 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <COREv4 COREBOOT>
WARNING: L1 data cache covers fewer APIC IDs than a core (0 < 1)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
random: unblocking device.
ioapic0 <Version 2.0> irqs 0-119
Launching APs: 3 1 2
random: entropy device external interface
wlan: mac acl policy registered
kbd0 at kbdmux0
WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 15.0.
efirtc0: <EFI Realtime Clock>
efirtc0: registered as a time-of-day clock, resolution 1.000000s
smbios0: <System Management BIOS> at iomem 0x77535000-0x7753501e
smbios0: Version: 3.3, BCD Revision: 3.3
aesni0: <AES-CBC,AES-CCM,AES-GCM,AES-ICM,AES-XTS,SHA1,SHA256>
acpi0: <COREv4 COREBOOT>
acpi0: Power Button (fixed)
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 19200000 Hz quality 950
Event timer "HPET" frequency 19200000 Hz quality 550
Event timer "HPET1" frequency 19200000 Hz quality 440
Event timer "HPET2" frequency 19200000 Hz quality 440
Event timer "HPET3" frequency 19200000 Hz quality 440
Event timer "HPET4" frequency 19200000 Hz quality 440
cpu0: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x1000-0x103f mem 0x90000000-0x90ffffff,0x80000000-0x8fffffff at device 2.0 on pci0
vgapci0: Boot video device
xhci0: <XHCI (generic) USB 3.0 controller> mem 0x91100000-0x9110ffff at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
pci0: <memory, RAM> at device 20.2 (no driver attached)
pci0: <simple comms> at device 22.0 (no driver attached)
ahci0: <AHCI SATA controller> port 0x1060-0x1067,0x1068-0x106b,0x1040-0x105f mem 0x91118000-0x91119fff,0x9111f000-0x9111f0ff,0x9111e000-0x9111e7ff at device 23.0 on pci0
ahci0: AHCI v1.31 with 2 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
sdhci_pci0: <Generic SD HCI> mem 0x9111c000-0x9111cfff at device 26.0 on pci0
sdhci_pci0: 1 slot(s) allocated
mmc0: <MMC/SD bus> on sdhci_pci0
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
igc0: <Intel(R) Ethernet Controller I225-V> mem 0x7f400000-0x7f4fffff,0x7f600000-0x7f603fff at device 0.0 on pci1
igc0: EEPROM V1.57-0 eTrack 0x80000185
igc0: Using 1024 TX descriptors and 1024 RX descriptors
igc0: Using 4 RX queues 4 TX queues
igc0: Using MSI-X interrupts with 5 vectors
igc0: Ethernet address: 64:62:66:22:30:03
igc0: netmap queues/slots: TX 4/1024, RX 4/1024
pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pci2: <ACPI PCI bus> on pcib2
igc1: <Intel(R) Ethernet Controller I225-V> mem 0x7f700000-0x7f7fffff,0x7f900000-0x7f903fff at device 0.0 on pci2
igc1: EEPROM V1.57-0 eTrack 0x80000185
igc1: Using 1024 TX descriptors and 1024 RX descriptors
igc1: Using 4 RX queues 4 TX queues
igc1: Using MSI-X interrupts with 5 vectors
igc1: Ethernet address: 64:62:66:22:30:04
igc1: netmap queues/slots: TX 4/1024, RX 4/1024
pcib3: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
igc2: <Intel(R) Ethernet Controller I225-V> mem 0x7fa00000-0x7fafffff,0x7fc00000-0x7fc03fff at device 0.0 on pci3
igc2: EEPROM V1.57-0 eTrack 0x80000185
igc2: Using 1024 TX descriptors and 1024 RX descriptors
igc2: Using 4 RX queues 4 TX queues
igc2: Using MSI-X interrupts with 5 vectors
igc2: Ethernet address: 64:62:66:22:30:05
igc2: netmap queues/slots: TX 4/1024, RX 4/1024
pcib4: <ACPI PCI-PCI bridge> at device 28.4 on pci0
pci4: <ACPI PCI bus> on pcib4
igc3: <Intel(R) Ethernet Controller I225-V> mem 0x7fd00000-0x7fdfffff,0x7ff00000-0x7ff03fff at device 0.0 on pci4
igc3: EEPROM V1.57-0 eTrack 0x80000185
igc3: Using 1024 TX descriptors and 1024 RX descriptors
igc3: Using 4 RX queues 4 TX queues
igc3: Using MSI-X interrupts with 5 vectors
igc3: Ethernet address: 64:62:66:22:30:06
igc3: netmap queues/slots: TX 4/1024, RX 4/1024
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
hdac0: <Intel (0x4b58) HDA Controller> mem 0x91114000-0x91117fff,0x91000000-0x910fffff at device 31.3 on pci0
pci0: <serial bus> at device 31.5 (no driver attached)
acpi_syscontainer0: <System Container> port 0x2e-0x2f on acpi0
hwpstate_intel0: <Intel Speed Shift> on cpu0
hwpstate_intel1: <Intel Speed Shift> on cpu1
hwpstate_intel2: <Intel Speed Shift> on cpu2
hwpstate_intel3: <Intel Speed Shift> on cpu3
Timecounter "TSC" frequency 1996801611 Hz quality 1000
Timecounters tick every 1.000 msec
ugen0.1: <Intel XHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
mmc0: CMD13 failed, RESULT: 2
mmc0: CMD13 failed, RESULT: 2
mmc0: CMD13 failed, RESULT: 2
mmc0: CMD13 failed, RESULT: 2
mmc0: CMD13 failed, RESULT: 2
mmc0: Card at relative address 2 failed to set HS200 timing
mmc0: Card at relative address 2 failed to select
mmcsd0: Error reading EXT_CSD Timeout
device_attach: mmcsd0 attach returned 6
hdacc0: <Intel Elkhart Lake HDA CODEC> at cad 2 on hdac0
hdaa0: <Intel Elkhart Lake Audio Function Group> at nid 1 on hdacc0
pcm0: <Intel Elkhart Lake (HDMI/DP 8ch)> at nid 4 on hdaa0
Trying to mount root from ufs:/dev/ufs/OPNsense_Install [ro,noatime]...
uhub0: 16 ports with 16 removable, self powered
Root mount waiting for: usbus0 CAM
Root mount waiting for: usbus0 CAM
usb_msc_auto_quirk: UQ_MSC_NO_GETMAXLUN set for USB mass storage device USB Disk 2.0 (0xffff:0x5678)
ugen0.2: <USB Disk 2.0> at usbus0
umass0 on uhub0
umass0: <USB Disk 2.0, class 0/0, rev 2.00/2.00, addr 1> on usbus0
umass0: SCSI over Bulk-Only; quirks = 0x0100
umass0:2:0: Attached to scbus2
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
ada0 at ahcich1 bus 0 scbus1 target 0 lun 0
ada0: <Protectli 1TB M.2 SBFM61.5> ACS-4 ATA SATA 3.x device
ada0: Serial Number 03E407381E8D00206471
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 976762MB (2000409264 512 byte sectors)
da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
da0: <VendorCo ProductCode 2.00> Removable Direct Access SPC-2 SCSI device
da0: Serial Number KT20200000000060
da0: 40.000MB/s transfers
da0: 3840MB (7864320 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
Dual Console: Serial Primary, Video Secondary
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
igc0: link state changed to UP
igc1: link state changed to UP
lo0: link state changed to UP
It just hangs here forever
It's not "hanging", its console settings are misconfigured or you were hit by a regression ("fix" in FreeBSD) that changed console preferences for a bit in 25.1.x.
Quickest road to success: either use the 24.7 image now or 25.7 which comes out Wednesday.
Cheers,
Franco
ProTectli came out with a upgrade to their bootloader. Any thoughts as to if it may be part of the issue?