Hey community,
I am new in the opnsense area.
If I do a speedtest it is all the time ca. 100 MB/s. If I connect it with my alternative router it comes the full bandwith.
Setup:
ISP / Modem ( Speedport SMART ) -----> OPNsense ( N5105 ) -----> AP ( Asus DSL 68U )
OPNsense 23.7-amd64
FreeBSD 13.2-RELEASE-p1
OpenSSL 1.1.1u 30 May 2023
Intel(R) Celeron(R) N5105 @ 2.00GHz (4 cores, 4 threads)
downlink: 104.700
uplink: 36,213
ping: 11 ms
What I did:
-- exchange the cable ( different CAT 7 cables )
-- add Parent WAN
-- disable / enable unbound/adguard
-- change the parameters for optimizing from teklager and disabled flowcontrol ( see below )
does someone has a hint for me?
my loader.conf :
root@OPNsense:/var/db/etcupdate/current/etc # cat /boot/loader.conf
##############################################################
# This file was auto-generated using the rc.loader facility. #
# In order to deploy a custom change to this installation, #
# please use /boot/loader.conf.local as it is not rewritten, #
# or better yet use System: Settings: Tunables from the GUI. #
##############################################################
loader_brand="opnsense"
loader_logo="hourglass"
loader_menu_title=""
autoboot_delay="3"
# Vital modules that are not in FreeBSD's GENERIC
# configuration will be loaded on boot, which makes
# races with individual module's settings impossible.
carp_load="YES"
if_bridge_load="YES"
if_enc_load="YES"
if_gif_load="YES"
if_gre_load="YES"
if_lagg_load="YES"
if_tap_load="YES"
if_tun_load="YES"
if_vlan_load="YES"
pf_load="YES"
pflog_load="YES"
pfsync_load="YES"
# ZFS standard environment requirements
kern.geom.label.disk_ident.enable="0"
kern.geom.label.gptid.enable="0"
vfs.zfs.min_auto_ashift=12
opensolaris_load="YES"
zfs_load="YES"
# dynamically generated console settings follow
#comconsole_speed
#boot_multicons
#boot_serial
#kern.vty
console="vidconsole"
# dynamically generated tunables settings follow
dev.igc.0.fc="0"
dev.igc.1.fc="0"
dev.igc.2.fc="0"
dev.igc.3.fc="0"
hw.ibrs_disable="0"
hw.igc.rx_process_limit="-1"
hw.igc.tx_process_limit="-1"
hw.ixl.enable_head_writeback="0"
hw.syscons.kbd_reboot="0"
kern.ipc.maxsockbuf="4262144"
kern.ipc.nmbclusters="1000000"
kern.randompid="1"
legal.intel_igc.license_ack="-1"
net.enc.in.ipsec_bpf_mask="2"
net.enc.in.ipsec_filter_mask="2"
net.enc.out.ipsec_bpf_mask="1"
net.enc.out.ipsec_filter_mask="1"
net.inet.icmp.drop_redirect="1"
net.inet.icmp.icmplim="0"
net.inet.icmp.log_redirect="0"
net.inet.icmp.reply_from_interface="1"
net.inet.ip.accept_sourceroute="0"
net.inet.ip.forwarding="1"
net.inet.ip.intr_queue_maxlen="1000"
net.inet.ip.portrange.first="1024"
net.inet.ip.random_id="1"
net.inet.ip.redirect="0"
net.inet.ip.sourceroute="0"
net.inet.tcp.blackhole="2"
net.inet.tcp.delayed_ack="0"
net.inet.tcp.drop_synfin="1"
net.inet.tcp.log_debug="0"
net.inet.tcp.recvspace="65228"
net.inet.tcp.sendspace="65228"
net.inet.tcp.syncookies="1"
net.inet.tcp.tso="1"
net.inet.udp.blackhole="1"
net.inet.udp.checksum="1"
net.inet.udp.maxdgram="57344"
net.inet6.ip6.forwarding="1"
net.inet6.ip6.intr_queue_maxlen="1000"
net.inet6.ip6.prefer_tempaddr="0"
net.inet6.ip6.redirect="0"
net.inet6.ip6.use_tempaddr="0"
net.link.bridge.pfil_bridge="1"
net.link.bridge.pfil_local_phys="0"
net.link.bridge.pfil_member="0"
net.link.bridge.pfil_onlyip="0"
net.link.ether.inet.log_arp_movements="1"
net.link.ether.inet.log_arp_wrong_iface="1"
net.link.tap.user_open="1"
net.link.vlan.mtag_pcp="1"
net.local.dgram.maxdgram="8192"
net.pf.share_forward="1"
net.pf.share_forward6="1"
net.route.multipath="0"
security.bsd.see_other_gids="0"
security.bsd.see_other_uids="0"
vfs.read_max="32"
vm.pmap.pti="1"
I think there's something wrong with 23.7. I'm not getting the same peak speed I used to get, and I'm burning a lot more CPU. It looks like ISRs are doing something they didn't do before.
Quote from: srepper on July 31, 2023, 11:51:57 PM
Hey community,
I am new in the opnsense area.
If I do a speedtest it is all the time ca. 100 MB/s. If I connect it with my alternative router it comes the full bandwith.
Setup:
ISP / Modem ( Speedport SMART ) -----> OPNsense ( N5105 ) -----> AP ( Asus DSL 68U )
OPNsense 23.7-amd64
FreeBSD 13.2-RELEASE-p1
OpenSSL 1.1.1u 30 May 2023
Intel(R) Celeron(R) N5105 @ 2.00GHz (4 cores, 4 threads)
downlink: 104.700
uplink: 36,213
ping: 11 ms
What I did:
-- exchange the cable ( different CAT 7 cables )
-- add Parent WAN
-- disable / enable unbound/adguard
-- change the parameters for optimizing from teklager and disabled flowcontrol ( see below )
Maybe a silly question but at which speed are your interfaces negotiated?
Quote from: JustMeHere on August 03, 2023, 07:15:09 PM
I think there's something wrong with 23.7. I'm not getting the same peak speed I used to get, and I'm burning a lot more CPU. It looks like ISRs are doing something they didn't do before.
This looks really weird the IRQs increased, and I believe you have same configuration setup as per per upgrade?
I have as well an N5105 CPU didn't yet upgrade. Its on schedule next week so will see what will be the outcome.
Regards,
S.
Just registered to share my experience.
I too ran into the same issue after upgrading to 23.7 on my j6314 appliance. My DL speeds decreased significantly. I was convinced I had an ISP issue originally.
What caught my attention was my cronjob to run the speedtest every morning was no longer working as I have a specific server ID set. I went into the GUI and noticed my list of available servers was not normal and showing servers hundreds of miles away from me.
I then went into the Speedtest reporting tab and ticked the Help toggle. This brings up a few options above the Log Section. I noticed Speedtest was using HTTP, I switched this over to "switch to socket speedtest" and noticed my local servers reappeared and ran a test. All normal again!
My guess is that when the plugin was reinstalled after the 23.7 upgrade, speedtest defaulted to HTTP tests.
Hopefully this solves the issue for you!