Hello, Im really hoping someone can help me out with this issue, because it is driving me nuts!
I am running Opnsense (20.7.5) on a Dell optiplex 3020 SFF desktop( 3rd gen I3, 8GB ram 256GB SATA SSD ). I am using the onboard NIC as my WAN interface, that connects to my Virgin Media Router in modem mode. I have also added an Intel NIC ( I cant remember the model number now but I think it is a Pro 1000T) as my LAN interface. My setup is really uncomplicated from what I can tell, but for some reason my LAN interface goes up and down at random times.
Lastnight it was down for 6 hours while we were asleep, but today most of the day I could use it with no noticeable issues, but then it dropped again while someone was in the middle of a Zoom call this evening.
I have checked dmesg and can see the interface go Up / Down, and can even see holes in the metrics I am getting from OpnSense, but still can work out a cause. I have even tried three different switches connected to the lan interface to see if they were the problem, but still no dice.
Some relevant (I hope) output is attached, and I would love to hear any suggestions.
root@OPNsense:~ # pciconf -l
hostb0@pci0:0:0:0: class=0x060000 card=0x05771028 chip=0x01508086 rev=0x09 hdr=0x00
pcib1@pci0:0:1:0: class=0x060400 card=0x05771028 chip=0x01518086 rev=0x09 hdr=0x01
-- trim --
em1@pci0:0:25:0: class=0x020000 card=0x052c1028 chip=0x15028086 rev=0x04 hdr=0x00
em0@pci0:1:0:0: class=0x020000 card=0xa01f8086 chip=0x10d38086 rev=0x00 hdr=0x00
[/code]
root@OPNsense:~ # ifconfig
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=802008<VLAN_MTU,WOL_MAGIC>
ether 68:05:ca:b5:f3:37
inet6 fe80::%em0 prefixlen 64 scopeid 0x1
inet <MY PUBLIC IP> netmask 0xffffff00 broadcast <PUBLIC BROADCAST>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
em1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=802008<VLAN_MTU,WOL_MAGIC>
ether b8:ca:3a:a8:86:f6
inet6 fe80::baca:3aff:fea8:86f6%em1 prefixlen 64 scopeid 0x2
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
root@OPNsense:~ # tail -n 20 /var/log/dmesg.today
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
arp: 192.168.1.167 moved from 24:da:33:d6:bc:42 to 40:4d:7f:15:4c:9f on em1
arp: 192.168.1.167 moved from 40:4d:7f:15:4c:9f to 24:da:33:d6:bc:42 on em1
arp: 192.168.1.164 moved from 50:0f:f5:ad:2c:40 to 24:da:33:d6:bc:42 on em1
em1: link state changed to DOWN
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
em1: link state changed to UP
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
em1: link state changed to DOWN
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
em1: link state changed to UP
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
While posting this output, I have noticed that dmesg,today contains output for a reboot I didnt realise happened, also there are a lot of messages for pid 90870 (syslog-ng), jid 0, uid 0: exited on signal 6 (core dumped) that I will have a look into (the syslog messages seem to be more to do with the reboot, than linked to any of the up/down of the interfaces).
Hi!
Had problems with two Optiplex SFF with Intel NIC cards added, here the WAN was going down (the built-in NIC). Started on both after one of the recent OPNsense updates and was correlated with turning on suricata in IPS mode.
https://forum.opnsense.org/index.php?topic=19851.0
Problem resolved by fresh install and config import...
Have you tried a different Intel NIC card?
Thanks for your response chemlud,
I have tried a brand new install, and that is what I am using now, but that doesnt seem to have had any affect. I am also not using suricata, and am just running a base install with the prometheus exporter added. I am planning to try another Intel NIC, and have a i350T2 on the way, but was hoping I could find a log or something that would give me some useful info about what was going on in the mean time.
Just noticed, that the dashboard doesnt show any sign of a reboot, but I can see it clearly i dmesg.