46
23.1 Legacy Series / Re: Occasional interface "attached" event on all interfaces
« on: May 15, 2023, 03:37:40 pm »
A few more screenshots (second post due to size limit...)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
pid 59481 (eastpect), jid 0, uid 0: exited on signal 11
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
193.368040 [ 851] iflib_netmap_config txr 4 rxr 4 txd 2048 rxd 2048 rbufsz 2048
193.368304 [ 851] iflib_netmap_config txr 4 rxr 4 txd 2048 rxd 2048 rbufsz 2048
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
pid 48117 (eastpect), jid 0, uid 0: exited on signal 11
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
223.756165 [ 851] iflib_netmap_config txr 4 rxr 4 txd 2048 rxd 2048 rbufsz 2048
223.756223 [ 851] iflib_netmap_config txr 4 rxr 4 txd 2048 rxd 2048 rbufsz 2048
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
ix0: link state changed to DOWN
ix0_vlan10: link state changed to DOWN
ix0_vlan11: link state changed to DOWN
ix0_vlan12: link state changed to DOWN
ix0_vlan13: link state changed to DOWN
ix0: link state changed to UP
ix0_vlan10: link state changed to UP
ix0_vlan11: link state changed to UP
ix0_vlan12: link state changed to UP
ix0_vlan13: link state changed to UP
It can be. Discussion at https://github.com/opnsense/core/issues/5104 about if it would make sense to integrate (and how).
Yeah I just did the builtin test. I remembered this was happening before I added the 2nd memory stick, so I pulled the original one to see if it happens again.
https://bsd-hardware.info/?probe=85256a78f6
Here's a hardware dump of the device. BIOS/UEFI is all the way up to date. This was an issue before I installed the RTL8125 interface.
Hah, right? Everyone has some story (or will). How do you do an automated backup? Where does the backup live?
ps -ax | grep <process name>
All your policies and policy configuration are intact and will be restored once you reactivate your subscription.
Team Zenarmor
I had to reapply my license as well, but it did not affect my policies.