Home
Help
Search
Login
Register
OPNsense Forum
»
Archive
»
15.1 Legacy Series
»
[SOLVED] Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
« previous
next »
Print
Pages: [
1
]
Author
Topic: [SOLVED] Initial LAN DHCP server from CLI console truncated from *.100 to *.10. (Read 24942 times)
rcpa0
Newbie
Posts: 6
Karma: 1
[SOLVED] Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
on:
May 07, 2015, 06:01:51 am »
I typed in the starting DHCP address pool as *.*.*.100
and ending with *.*.*.245
It all looks fine, but the web GUI shows the staring address pool as *.*.*.10 instead of .100.
Updating the web GUI does correctly change the starting address to *.100.
This issue exists in pfSense 2.2 and 2.2.2 as well.
«
Last Edit: May 12, 2015, 03:09:16 pm by franco
»
Logged
rcpa0
Newbie
Posts: 6
Karma: 1
Re: Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
Reply #1 on:
May 07, 2015, 06:21:35 am »
web GUI >
Configure WAN Interface >
Static IP Configuration >
Upstream Gateway is empty instead of what I filled out in CLI console.
Logged
franco
Administrator
Hero Member
Posts: 17473
Karma: 1587
Re: Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
Reply #2 on:
May 07, 2015, 04:17:48 pm »
I could not reproduce both of these reports.
The DHCP range for LAN is set up correctly.
The Gateway was created for LAN and properly added to interface configuration.
The DHCP setting for WAN works.
The static IP setting for WAN including setting the gateway works.
If the error persists please provide accurate steps to reproduce this.
Logged
rcpa0
Newbie
Posts: 6
Karma: 1
Re: Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
Reply #3 on:
May 08, 2015, 07:08:35 pm »
From CLI console:
4) Reset to factory defaults
3) Set interface IP address
LAN
192.168.1.50/24
Enable DHCP server:
Start: 192.168.1.100
End: 192.168.1.245
Keep https.
Go to client, get IP address (note it will be the correct .100 that you will get), login, finish guided setup, reload.
Log back in.
Go to DHCP Server > LAN tab
The Start address is 192.168.1.10 instead of the .100 set in CLI.
Logged
franco
Administrator
Hero Member
Posts: 17473
Karma: 1587
Re: Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
Reply #4 on:
May 09, 2015, 10:06:45 am »
The wizard will rewrite your settings made via the console. Please skip the wizard by clicking on the OPNsense logo in the top left corner.
Logged
rcpa0
Newbie
Posts: 6
Karma: 1
Re: [SOVLED] Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
Reply #5 on:
May 11, 2015, 09:35:01 am »
I think the settings entered in the CLI should be copied forward into the Wizard. Only questions not asked in CLI should be new and started with Wizard defaults.
Logged
franco
Administrator
Hero Member
Posts: 17473
Karma: 1587
Re: [SOVLED] Initial LAN DHCP server from CLI console truncated from *.100 to *.10.
«
Reply #6 on:
May 11, 2015, 01:57:43 pm »
It's not that easy, but given a proper fix I'm not against merging it.
Logged
Print
Pages: [
1
]
« previous
next »
OPNsense Forum
»
Archive
»
15.1 Legacy Series
»
[SOLVED] Initial LAN DHCP server from CLI console truncated from *.100 to *.10.